Home › Engine / Hybrid System ยท 3UR-FBE › ENGINE CONTROL › SFI SYSTEM

DTC    P050B    Cold Start Ignition Timing Performance

for Preparation Click here


DESCRIPTION

This monitor will run when the engine is started at an engine coolant temperature of -10 to 50°C (14 to 122°F). The DTC will be set after the engine idles for 13 seconds (2 trip detection logic).
The DTC is designed to monitor the ignition timing at cold start. When the engine is started at an engine coolant temperature of lower than 50°C (122°F), the ECM checks the ignition timing at engine idling. If the ignition timing advances beyond the specified level within 10 seconds, the ECM interprets this as a malfunction. The MIL is illuminated and a DTC is stored when the malfunction is detected in consecutive driving cycles (2 trip detection logic).

NOTICE:
When the negative battery terminal is disconnected during inspections or repairs, the ISC (Idle Speed Control) learning values are cleared. This DTC cannot be stored with the ISC learning values cleared.

HINT:
The ISC learning is performed when the engine is warmed up and has been idling for 5 minutes.


A153342E10


DTC No.
DTC Detection Condition
Trouble Area
P050B
Insufficient ignition timing retard at cold start (2-trip detection logic)
  1. Throttle body assembly
  2. Mass air flow meter
  3. PCV system
  4. Air cleaner filter element
  5. Air induction system
  6. VVT system
  7. ECM

MONITOR STRATEGY


Related DTCs
P050B: Cold start ignition timing performance
Required Sensors / Components (Main)
Throttle body assembly
Required Sensors / Components (Related)
Mass air flow meter
Engine Coolant Temperature (ECT) sensor
Frequency of Operation
Once per driving cycle
Duration
10 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
P0010, P0020 (VVT Oil Control Valve)
P0011, P0021 (VVT System - Advance)
P0012, P0022 (VVT System - Retard)
P0016, P0018 (VVT System - Misalignment)
P0013, P0023 (Exhaust VVT Oil Control Valve)
P0014, P0024 (Exhaust VVT System - Advance)
P0015, P0025 (Exhaust VVT System - Retard)
P0017, P0019 (Exhaust VVT System - Misalignment)
P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256, P2A00, P2A03 (Air Fuel Ratio Sensor)
P0102, P0103 (Mass Air Flow Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
P0171, P0172, P0174, P0175 (Fuel System)
P0301 - P0308 (Misfire)
P0335 (Crankshaft Position Sensor)
P1340 (Camshaft Position Sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT Sensor)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT Sensor)
P0351 - P0358 (Igniter)
P0500 (Vehicle Speed Sensor)
P0705 (Shift Lever Position Switch)
Battery voltage
8 V or more
Time after engine start
3 seconds or more
Starter
OFF
ECT at engine start
-10°C (14°F) or more
ECT
-10 to 50°C (14 to 122°F)
Engine idling time
3 seconds or more
Fuel-cut
OFF
Vehicle speed
Less than 3 km/h (1.875 mph)
Atmospheric pressure
76 kPa (570 mmHg) or more

TYPICAL MALFUNCTION THRESHOLDS


Accumulated time when ignition timing retard value is cut off
5 seconds or more

INSPECTION PROCEDURE

HINT:
  1. DTC P050B may be set when the engine has the symptoms listed below. If necessary, check the trouble areas listed below.

    Symptom
    Factor
    Trouble Area
    Low idle speed when engine is cold (immediately after engine start)
    Excessive engine friction
    1. Engine oil deterioration
    2. Drive belt tension
    3. A/C compressor
    4. Generator
    5. Vane pump
    Rough idle when engine is cold (immediately after engine start)
    Abnormal combustion
    Fuel quality
  2. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P050B)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.
    Result 
    Result
    Proceed to
    P050B is output
    A
    P050B and other DTCs are output
    B

    HINT:
    If any DTCs other than P050B are output, troubleshoot those DTCs first.



NG
GO TO DTC CHART (Click here)
OK


2.INSPECT THROTTLE BODY
  1. Check that there are no deposits around the throttle valve.

    OK:
    No deposits around the throttle valve.



NG
Go to step 8
OK


3.PERFORM ACTIVE TEST USING TECHSTREAM (OCV OPERATION)
  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1) or Control the VVT System (Bank 2).

  1. Check the engine speed while operating the Oil Control Valve (OCV) using the Techstream.

    OK:
    Tester Operation
    Specified Condition
    OCV OFF
    Normal engine speed
    OCV ON
    Soon after OCV switched from OFF to ON, engine idles roughly or stalls



NG
Go to step 9
OK


4.CHECK PCV SYSTEM
  1. Start the engine.

  1. Pinch the positive crankcase PCV hose.

  1. Check the engine speed.

    OK:
    The engine speed rises when the PCV hose is pinched.



NG
Go to step 10
OK


5.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
  1. Visually check that the air cleaner filter element is not excessively contaminated with dirt or oil.

    OK:
    The air cleaner filter element is not excessively contaminated with dirt or oil.



NG
Go to step 11
OK


6.CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leaks .

    OK:
    No leak from the air induction system.



NG
Go to step 12
OK


7.REPLACE MASS AIR FLOW METER
  1. Replace the mass air flow meter (Click here).



NEXT
Go to step 13

8.REPAIR OR REPLACE THROTTLE BODY
  1. Repair or replace the throttle body (Click here).



NEXT
Go to step 13

9.CHECK AND REPAIR VVT SYSTEM


NEXT
Go to step 13

10.REPAIR OR REPLACE PCV SYSTEM


NEXT
Go to step 13

11.REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY


NEXT
Go to step 13

12.REPAIR OR REPLACE AIR INDUCTION SYSTEM

NEXT


13.CHECK WHETHER DTC OUTPUT RECURS (DTC P050B)

NOTICE:
For this operation, the engine must be cold (the same level as the engine coolant temperature recorded in the freeze frame data).

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Switch the ECM from normal mode to check mode using the Techstream (Click here).

  1. Start the engine and idle it for one minute.

  1. Check that the idling is stable and fast.

    OK:
    Stable fast idle

  1. Read the DTCs.

    OK:
    No DTC is output.



NG
REPLACE ECM (Click here)
OK

END