Home › Vehicle Interior › HEATING / AIR CONDITIONING › FRONT AIR CONDITIONING UNIT

FRONT AIR CONDITIONING UNIT > INSTALLATION

for Preparation Click here



1. INSTALL FRONT AIR CONDITIONING UNIT


I104401
  1. Temporarily tighten the air conditioning unit with the 3 bolts and 2 screws.



2. INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY


I104432
  1. Connect the connector and clamp and install the wire harness.



  1. Install the instrument panel reinforcement.

    1. for Passenger Side:
      Using a 12 mm hexagon wrench, install the 2 collars.

      Torque:
      18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    2. for Passenger Side:
      Using a T40 "TORX" socket, install the 2 "TORX" bolts.

      Torque:
      18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    3. for Driver Side:
      Install the 3 bolts and 2 caps.



    4. Install the instrument panel reinforcement with the 3 bolts and nut.

      1. for Nut

      Torque:
      9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



      I104455E01



    I104401
  1. Tighten the air conditioning unit with the 3 bolts and 2 screws.

    1. for Bolt

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Connect the connectors and clamps and install the wire harness.



  1. Install the ground wire with the bolt.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }



    I104431



3. INSTALL NO. 1 ECU INTEGRATION BRACKET


I104430
  1. Install the ECU integration bracket with the bolt and nut.

  1. Connect the connectors and clamp.



4. INSTALL TURN SIGNAL FLASHER ASSEMBLY


I104429
  1. Install the turn signal flasher with the nut.

  1. Connect the connector.



5. INSTALL MAIN BODY ECU


I104428
  1. Install the main body ECU with the bolt and nut.

  1. Connect the connectors and clamp.



6. INSTALL REAR NO. 2 AIR DUCT


I104426
  1. Engage the 3 claws and install the air duct.



7. INSTALL REAR NO. 1 AIR DUCT


I104427
  1. Engage the 3 claws and install the air duct.



8. INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY


    C179208E01
  1. Install the transmission floor shift with the 4 bolts. Tighten the bolts in the order shown in the illustration.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

  1. Connect the clamp and 2 connectors.



9. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    C179207
  1. Install the cable outer of the transmission control cable to the shift lever retainer, and install a new clip.



    C179205E01
  1. Connect the transmission control cable end to the shift lever.

    NOTICE:
    Make sure to install the cable end so that the inner cable is not twisted. Confirm that the cable end's ridged side is facing upward.



10. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY (for 8 Speakers)


  1. Engage the 5 claws to install the instrument panel.


    B192375

  1. Install the 3 <C> bolts and 2 <E> nuts.



  1. Install the 2 <F> passenger airbag bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



    B188245E01

  1. Connect the connectors and engage the clamps.



  1. Install the wire harness with the bolt.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }



    B188244



    B192371
  1. Connect the airbag connector.



11. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY (for 14 Speakers)


  1. Engage the 5 claws to install the instrument panel.


    B192375

  1. Install the 3 <C> bolts and 2 <E> nuts.



  1. Install the 2 <F> passenger airbag bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



    B188245E01

  1. Connect the connectors and engage the clamps.



  1. Install the wire harness with the bolt.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }



    B192365



    B192371
  1. Connect the airbag connector.



12. INSTALL STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)


C180952E01
  1. Install the steering column with the bolt and 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. Connect the connectors and wire harness clamps.



13. INSTALL STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)


C180953E01
  1. Install the steering column with the bolt and 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. Connect the connectors and wire harness clamps.



14. INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY


C154524E01
  1. Align the matchmarks on the steering column and install the steering intermediate shaft.

  1. Install the bolt.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



15. INSTALL NO. 3 AIR DUCT SUB-ASSEMBLY


    C154523
  1. Install the air duct with the bolt.



16. INSTALL NO. 1 INSTRUMENT PANEL SAFETY PAD INSERT


B192337
  1. Connect the connector and engage the clamp.

  1. Engage the 2 claws to install the safety pad insert.

  1. Install the 4 <A> bolts.



17. INSTALL REAR NO. 4 AIR DUCT


I104424
  1. Engage the 4 claws and install the air duct.

  1. Install the clip.



18. INSTALL REAR NO. 3 AIR DUCT


I104425
  1. Engage the 4 claws and install the air duct.

  1. Install the clip.



19. INSTALL STEREO COMPONENT AMPLIFIER ASSEMBLY (for 14 Speakers)


    B190161
  1. Install the amplifier with the 3 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the 4 connectors.



20. INSTALL AUDIO AMPLIFIER COVER (for 14 Speakers)


B190162
  1. Set the cover on the stereo amplifier assembly.

  1. Engage the 3 clips.



21. INSTALL FRONT RH SEAT ASSEMBLY (for RH Side)
  1. Install the front seat.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Connect the seat wire connectors under the seat.

  1. Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



    B167189
  1. Operate the leg support adjustment switch to move the seat cushion to the closed position.

  1. Operate the power seat switch to move the seat to the rearmost position.



    B194824
  1. Install the 2 bolts.

    Torque:
    37 N*m{ 374 kgf*cm , 27 ft.*lbf }

  1. Operate the power seat switch to move the seat to the foremost position.



    B191041
  1. Install the 2 bolts.

    Torque:
    37 N*m{ 374 kgf*cm , 27 ft.*lbf }



22. INSTALL SEAT TRACK OUTER COVER RH (for RH Side)


    B200255
  1. Engage the 2 claws to install the seat track cover.



23. INSTALL SEAT TRACK INNER COVER RH (for RH Side)


    B191067
  1. Engage the 2 claws to install the seat track cover.



24. INSTALL FRONT SEAT HEADREST ASSEMBLY (for RH Side)


25. INSTALL FRONT LH SEAT ASSEMBLY (for LH Side)
  1. Install the front seat.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Connect the seat wire connectors under the seat.

  1. Operate the seat track adjusting handle to move the seat to the rearmost position.



    B191042
  1. Install the 2 bolts.

    Torque:
    37 N*m{ 374 kgf*cm , 27 ft.*lbf }

  1. Operate the seat track adjusting handle to move the seat to the foremost position.



    B191041
  1. Install the 2 bolts.

    Torque:
    37 N*m{ 374 kgf*cm , 27 ft.*lbf }



26. INSTALL SEAT TRACK OUTER COVER LH (for LH Side)


    B200255
  1. Engage the 2 claws to install the seat track cover.



27. INSTALL SEAT TRACK INNER COVER LH (for LH Side)


    B191067
  1. Engage the 2 claws to install the seat track cover.



28. INSTALL FRONT SEAT HEADREST ASSEMBLY (for LH Side)


29. INSTALL FRONT NO. 4 SPEAKER ASSEMBLY (for 14 Speakers)


B165751E01
  1. Connect the connector.

  1. Temporarily install the speaker by aligning the positioning pins of the speaker with the instrument panel.

  1. Install the speaker with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

    NOTICE:
    1. Do not touch the cone part of the speaker.
    2. When installing the speaker to the instrument panel, be careful that the wires do not get caught between the parts.



30. INSTALL NO. 3 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


B192348
  1. Engage the 6 clips and 2 claws to install the speaker panel.



31. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY RH


E161074
  1. Connect the speaker connector.

  1. Temporarily install the speaker by aligning the positioning pins of the speaker with the instrument panel.

  1. Install the speaker with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

    NOTICE:
    1. Do not touch the cone part of the speaker.
    2. When installing the speaker to the instrument panel, be careful that the wires do not get caught between the parts.



32. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


B192350
  1. Engage the 4 clips and claw install the speaker panel.



33. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY LH


E161075
  1. Connect the speaker connector.

  1. Temporarily install the speaker by aligning the positioning pins of the speaker with the instrument panel.

  1. Install the speaker with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

    NOTICE:
    1. Do not touch the cone part of the speaker.
    2. When installing the speaker to the instrument panel, be careful that the wires do not get caught between the parts.



34. INSTALL INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


B192346
  1. Engage the 4 clips and claw and install the speaker panel.



35. INSTALL NO. 2 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY


    B192344
  1. Engage the clip and install the box door.

  1. Install the 6 <B> screws.



36. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY RH


    B192341
  1. Engage the 4 claws and install the finish panel.

  1. Install the 3 <D> screws and bolt <A>.



37. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


B192340
  1. Engage the 2 guides and 4 claws and install the under cover.



38. INSTALL FRONT PILLAR GARNISH RH


    B190132E01
  1. Remove the protective cover.



  1. Engage the claw to install the front pillar garnish.


    B193062

  1. Install the assist grip with the 2 bolts.

    Torque:
    9.7 N*m{ 99 kgf*cm , 86 in.*lbf }

  1. Engage the 2 claws to install the 2 assist grip plugs.



39. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Install the front door opening trim weatherstrip RH.



40. INSTALL COWL SIDE TRIM BOARD RH


    B190152
  1. Engage the 2 clips to install the cowl side trim board.

  1. Install the clip.



41. INSTALL FRONT DOOR SCUFF PLATE RH


B190151
  1. Engage the 9 claws to install the scuff plate.



42. INSTALL INSTRUMENT SIDE PANEL RH


    B192339
  1. Engage the 3 guides and 3 claws and install the side panel.



43. INSTALL NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System)


E159006
  1. Connect the connectors.

  1. Insert the navigation receiver as shown in the illustration to engage the 3 clips on its backside.

    NOTICE:
    When inserting the navigation receiver, do not press the knobs on it.



    B164792
  1. Install the navigation receiver with the 4 bolts.



44. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Radio Receiver)


E161045
  1. Connect the connectors.

  1. Insert the radio receiver and engage the 3 clips on its backside.

    NOTICE:
    When inserting the radio receiver, do not press its knobs.



    B164786
  1. Install the radio receiver with the 4 bolts.



45. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY


I104352
  1. Connect the connectors.

  1. Engage the 4 clips and install the panel.



46. INSTALL CENTER LOWER INSTRUMENT PANEL FINISH PANEL


    B192336
  1. Connect the connectors.

  1. Engage the 4 clips and 2 claws and install the finish panel.



47. INSTALL COMBINATION METER ASSEMBLY


    E141678
  1. Connect the connector and engage the clip and install the combination meter assembly.



    E161309
  1. Install the 4 screws.



48. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


B192335
  1. Engage the 12 clips and install the finish panel.

  1. Connect the 2 connectors and clamp.



    B192334
  1. Engage the 4 claws and install the instrument panel finish panel retainer.



49. INSTALL FRONT CONSOLE BOX


B188224
  1. Install the front console box with the 5 screws and 2 clips.

  1. Engage the 2 clamps.



50. INSTALL REAR CONSOLE BOX ASSEMBLY


B192330
  1. Engage the 6 claws and install the rear console box.

  1. Install the 2 screws and 4 bolts.



    B188223
  1. Connect the connectors.



51. INSTALL CONSOLE BOX CARPET


B188222
  1. Install the console box carpet.



52. INSTALL REAR CONSOLE BOX POCKET


B188221
  1. Install the rear console box pocket.



53. INSTALL REAR UPPER CONSOLE PANEL SUB-ASSEMBLY


    B192328
  1. Connect the connectors.

  1. Engage the 6 clips and install the console panel.

  1. Install the clip.



54. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY


    B161742
  1. Engage the 12 clips and install the console panel.



55. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


    B167312
  1. Install the shift lever knob and twist it in the direction indicated by the arrow.



56. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH


B192333
  1. Engage the 2 claws and install the sensor.

  1. Connect the connectors.

  1. Engage the 4 clips and claw and install the finish panel.

  1. Install the 2 <A> bolts.



57. INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    B192511
  1. Connect the hood lock control cable assembly to the hood lock control lever sub-assembly.

  1. engage the 3 claws to install the hood lock lever



58. INSTALL INSTRUMENT SIDE PANEL LH


    B192332
  1. Engage the 4 guides and 3 claws and install the side panel.



59. INSTALL FRONT PILLAR GARNISH LH

HINT:
Use the same procedure for both sides.



60. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Install the front door opening trim weatherstrip LH.



61. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure for both sides.



62. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure for both sides.



63. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY


    C159216
  1. Install the turn signal switch with spiral cable to the steering column with the clamp.



    C180951
  1. Connect the 6 connectors to the turn signal switch with spiral cable.



64. INSTALL UPPER STEERING COLUMN COVER


C159215
  1. Attach the claw to install the upper steering column cover.

  1. Attach the 4 clips.



65. INSTALL LOWER STEERING COLUMN COVER


C181134
  1. Attach the 2 claws to install the lower steering column cover.

  1. Install the 2 screws.



66. INSTALL STEERING WHEEL ASSEMBLY


    C181135E01
  1. Align the matchmarks on the steering wheel and steering main shaft.

  1. Install the steering wheel set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



67. INSTALL STEERING PAD

NOTICE:
Do not use a steering pad that has been dropped.



    B166581
  1. Confirm that the ignition switch is turned off.

  1. Confirm that the negative battery terminal is disconnected.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Connect the horn terminal.

  1. Connect the airbag connector.

    NOTICE:
    1. Match the color of the airbag connector with that of the steering pad assembly, and install the airbag connector.
    2. Securely lock the locking button.

  1. Install the steering pad.



    C180935
  1. Using "TORX" socked wrench T30, tighten the 2 screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



68. INSTALL LOWER NO. 3 STEERING WHEEL COVER


    B166432
  1. Attach the 2 claws to install the cover.



69. INSTALL LOWER NO. 2 STEERING WHEEL COVER


    B166433
  1. Attach the 2 claws to install the cover.



70. INSTALL FRONT WIPER MOTOR AND LINK ASSEMBLY


    E161316
  1. Install the wiper motor and link assembly with the 4 bolts and nut.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the connector.



71. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E161314
  1. Engage the 6 claws and 8 guides and install the cowl top ventilator louver sub-assembly.

  1. Install the 2 clips.



72. INSTALL FRONT FENDER TO COWL SIDE SEAL LH

HINT:
Use the same procedure for both sides.



73. INSTALL FRONT FENDER TO COWL SIDE SEAL RH


    E161313
  1. Engage the claw and install the front fender to cowl side seal.



74. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E146308E02
  1. Clean any metal powder off the serrated part of the wiper arm with a round wire brush or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, and then stop the wiper motor in the automatic stop position.



    E161322E01
  1. Align the blade tip with the mark on the glass, as shown in the illustration.

    HINT:
    Hold down the wiper arm hinge with your hand while tightening the nut.

  1. Tighten the nut on the front wiper arm and blade.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.



75. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E146308E02
  1. Clean any metal powder off the serrated part of the wiper arm with a round wire brush or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, and then stop the wiper motor in the automatic stop position.



    E161321E01
  1. Align the blade tip with the mark on the glass, as shown in the illustration.

    HINT:
    Hold down the wiper arm hinge with your hand while tightening the nut.

  1. Tighten the nut on the front wiper arm and blade.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.



76. CONNECT HEATER WATER OUTLET HOSE A


I104461E01
  1. Connect the water hose onto the air conditioning unit.

    NOTICE:
    Perform the installation with the hose clip and mark at the correct angle.



77. CONNECT HEATER WATER INLET HOSE A


I104459E01
  1. Connect the water hose onto the air conditioning unit.

    NOTICE:
    Perform the installation with the hose clip and mark at the correct angle.



78. CONNECT COOLER REFRIGERANT LIQUID PIPE B


I104457
  1. Remove the attached vinyl tape from the pipe.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction pipe.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the 2 O-ring on the suction pipe and liquid pipe.

  1. Move the hook connector in the direction indicated by the arrow in the illustration.

  1. Insert the pipe joint into the fitting hole securely and tighten the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



79. INSPECT SHIFT LEVER POSITION
  1. When moving the shift lever from P to R with the ignition switch ON and the brake pedal depressed, make sure that it moves smoothly and correctly into position.

  1. Check that the shift lever does not stop when moving the shift lever from R to P, and check that the shift lever does not stick when moving the shift lever from D to S.

  1. Start the engine and make sure that the vehicle moves forward after moving the shift lever from N to D and moves rearward after moving the shift lever to R.
    If the operation cannot be done as specified, inspect the park/neutral position switch assembly and check the shift lever assembly installation condition.



80. ADJUST SHIFT LEVER POSITION
  1. Move the shift lever to N.



    C155901E02
  1. Fold back the transmission control cable adjust case cover. Then while sliding the slider toward the cable end side, press the lock piece from the back side to release the lock.



    C155902E02
  1. Check that the adjust case's spring is applying enough tension to the shift control cable. Then press the lock piece to set the lock.

    NOTICE:
    1. Use your hand to push the lock piece. Do not use any tools.
    2. Securely push the lock piece so that the slider's protrusion is above the lock piece.

  1. Return the cover of the adjust case to its original position.

  1. Inspect the operation after the adjustment.



81. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



82. ADD ENGINE COOLANT (for 3UR-FE)
  1. Add engine coolant.
    Standard Capacity 
    Item
    Specified Condition
    w/ Trailer Towing System
    14.6 liters (15.4 US qts., 12.8 Imp. qts.)
    w/o Trailer Towing System
    13.6 liters (14.4 US qts., 12.0 Imp. qts.)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).
    2. Please contact your Toyota dealer for further details.



    A151850E05
  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Install the reservoir cap.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Install the radiator cap.

  1. Start the engine and warm it up until the thermostat opens.

    HINT:
    The thermostat opening timing can be confirmed by pressing the radiator inlet hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. Maintain the engine speed at 2000 to 2500 rpm.

    NOTICE:
    1. Make sure that the radiator reservoir still has some coolant in it.
    2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
    3. If there is not enough coolant, the engine may burn out or overheat.
    4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the FULL line.
    5. Run the engine at 2000 rpm until the coolant level has stabilized.

  1. Press the inlet and outlet radiator hoses several times by hand to bleed air.

    CAUTION:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the fan.

  1. Stop the engine, and wait until the engine coolant cools down to ambient temperature.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A161780E01
  1. Check that the coolant level is between the FULL and LOW lines.
    If the coolant level is below the LOW line, repeat all of the procedures above.
    If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.



83. ADD ENGINE COOLANT (for 2UZ-FE)
  1. Add engine coolant.

    Standard capacity:
    9.7 liters (10.3 US qts, 8.5 Imp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).
    2. The thermostat opening timing can be confirmed by pressing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.



    A151850E03
  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Install the reservoir cap.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Install the radiator cap.

  1. Start the engine and warm it up until the thermostat opens.

    HINT:
    The thermostat opening timing can be confirmed by pressing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. Maintain the engine speed at 2000 to 2500 rpm and warm up the engine until the cooling fan operates.

    NOTICE:
    1. Make sure that the radiator reservoir still has some coolant in it.
    2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
    3. If there is not enough coolant, the engine may burn out or overheat.

  1. Press the inlet and outlet radiator hoses several times by hand to bleed air.

    CAUTION:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the fan.

  1. Stop the engine, and wait until the engine coolant cools down.



    A151850E04
  1. If the coolant level is below the LOW line, repeat all of the procedures above.



84. INSPECT FOR COOLANT LEAK (for 3UR-FE)


A161766E01

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.



85. INSPECT FOR COOLANT LEAK (for 2UZ-FE)

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A162054
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop. If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.



86. CHARGE REFRIGERANT



I100449E02

NOTICE:
Charge refrigerant in accordance with the equipment manual.

  1. Perform vacuum purging using a vacuum pump.

  1. Charge refrigerant HFC-134a (R134a).

    SST
    09985-20010   (09985-02010, 09985-02050, 09985-02060, 09985-02070, 09985-02080, 09985-02090, 09985-02110, 09985-02130, 09985-02140, 09985-02150)

    Standard:
    860 to 920 g (30.3 to 32.5 oz.)

    NOTICE:
    Do not start the engine before charging it with refrigerant as the cooler compressor does not work properly without sufficient refrigerant. This could cause the compressor to overheat.

    HINT:

    1. The relationship between the refrigerant charge amount and the pressure is as follows.


      I103968E01

    2. High Charge Range:
      If the refrigerant is overcharged, the pressure rises on the high-pressure side. High-pressure cut off frequently occurs. This causes insufficient cooling performance and also insufficient compressor lubrication.
    3. Low Charge Range:
      A shortage of refrigerant causes insufficient cooling performance and low circulation of refrigerant oil, which shortens the compressor life. Operation with insufficient coolant raises the refrigerant temperature and causes heat deterioration of the rubber seals and hoses. Cracking and subsequent refrigerant leakage may occur.


    1. Install the caps onto the service valves on the refrigerant line.



87. WARM UP ENGINE

NOTICE:
Warm up the engine at less than 2000 rpm for 1 minute or more after charging it with refrigerant.



88. INSPECT FOR REFRIGERANT LEAK
  1. After recharging the refrigerant gas, check for refrigerant gas leakage using a halogen leak detector.

  1. Perform the operation as follows:

    1. Stop the engine.
    2. Secure good ventilation (the halogen leak detector may react to volatile gases other than refrigerant, such as evaporated gasoline or exhaust gas).
    3. Repeat the test 2 or 3 times.
    4. Make sure that some refrigerant remains in the refrigeration system.
      When the compressor is off: approximately 392 to 588 kPa (4 to 6 kgf*cm2, 57 to 85 psi)

    HINT:
    It is impossible for the above pressure to be maintained if there is leakage.



    I042222E14
  1. Using the halogen leak detector, check the refrigerant line, especially at the connection points, for leakage.

  1. If no gas leakage is detected from the drain hose, remove the blower motor from the cooling unit. Insert the halogen leak detector sensor into the unit and perform the test.

  1. Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure switch and perform the test.



89. INSTALL NO. 1 ENGINE UNDER COVER


    A150108
  1. Hook the engine under cover onto the vehicle body as shown in the illustration.

  1. Install the 3 screws and 5 bolts.

    1. for bolt

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

    1. for screw

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }



90. INSPECT SRS WARNING LIGHT
  1. Inspect the SRS warning light (Click here).