AIR CONDITIONING PANEL > REMOVAL |
| 1. REMOVE FRONT DOOR SCUFF PLATE LH |
| 2. REMOVE COWL SIDE TRIM BOARD LH |
| 3. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
Separate the front door opening trim weatherstrip LH.
| 4. REMOVE INSTRUMENT SIDE PANEL LH |
![]() |
Apply protective tape, as shown in the illustration.
Using a moulding remover, disengage the 3 claws and 4 guides and remove the side panel.
| 5. REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
![]() |
Disengage the 3 claws.
Disconnect the hood lock control cable and remove the hood lock control lever sub-assembly.
| 6. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH |
![]() |
Remove the 2 <A> bolts.
Disengage the 4 clips and claw.
Disengage the 2 claws and separate the sensor.
Disconnect the connectors and remove the finish panel.
| 7. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY |
![]() |
Twist the shift lever knob in the direction indicated by the arrow and remove it.
| 8. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY |
![]() |
Disengage the 12 clips and remove the console panel.
| 9. REMOVE REAR UPPER CONSOLE PANEL SUB-ASSEMBLY |
![]() |
Move the shift lever to N.
Remove the clip.
Disengage the 6 clips and remove the console panel.
Disconnect the connector
| 10. REMOVE CONSOLE BOX CARPET |
![]() |
Remove the console box carpet.
| 11. REMOVE REAR CONSOLE BOX ASSEMBLY |
![]() |
Disconnect the connectors.
![]() |
Remove the 4 bolts and 2 screws.
Disengage the 6 claws and remove the rear console box.
| 12. REMOVE FRONT CONSOLE BOX |
![]() |
Disengage the 2 clamps.
Remove the 2 clips.
Remove the 5 screws and the front console box.
| 13. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY |
![]() |
Disengage the 4 claws and separate the instrument panel finish panel retainer.
![]() |
Disconnect the 2 connectors and clamp.
Disengage the 12 clips and remove the finish panel.
| 14. REMOVE COMBINATION METER ASSEMBLY |
![]() |
Remove the 4 screws.
![]() |
Disconnect the connector and disengage the clip and remove the combination meter assembly.
| 15. REMOVE CENTER LOWER INSTRUMENT PANEL FINISH PANEL |
![]() |
Disengage the 4 clips and 2 claws.
Disconnect the connectors and remove the finish panel.
| 16. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY |
![]() |
Disengage the 4 clips and separate the panel.
Disconnect the connectors and remove the panel.
| 17. REMOVE STEREO JACK ADAPTER ASSEMBLY |
![]() |
Disengage the 2 claws and remove the stereo jack adapter.
![]() |
Disconnect the connector.
| 18. REMOVE SEAT HEATER SWITCH LH (w/o Climate Control Seat System) |
![]() |
Disengage the 2 claws and remove the seat heater switch.
| 19. REMOVE SEAT HEATER SWITCH RH (w/o Climate Control Seat System) |
![]() |
Disengage the 2 claws and remove the seat heater switch.
| 20. REMOVE SEAT HEATER SWITCH LH (w/ Climate Control Seat System) |
![]() |
Disengage the 4 claws and remove the seat heater switch.
| 21. REMOVE SEAT HEATER SWITCH RH (w/ Climate Control Seat System) |
![]() |
Disengage the 4 claws and remove the seat heater switch.
| 22. REMOVE GLASS BREAKAGE SENSOR MICROPHONE |
![]() |
Disengage the 2 claws and remove the glass breakage sensor microphone.