Home › Engine / Hybrid System ยท 2UZ-FE › ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > INSTALLATION

for Preparation Click here



1. INSTALL VENTILATION VALVE SUB-ASSEMBLY


    A092803E03
  1. Apply adhesive to 2 or 3 threads.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



    A164275E01
  1. Install the ventilation valve sub-assembly.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }

    HINT:
    After applying the specified torque, rotate the ventilation valve clockwise with the port faced in the direction indicated in the illustration.



2. INSTALL VENTILATION VALVE COVER


3. INSTALL CRANKSHAFT POSITION SENSOR


    A153483
  1. Install the crankshaft position sensor with the bolt.

    Torque:
    6.5 N*m{ 65 kgf*cm , 58 in.*lbf }

  1. Connect the crankshaft position sensor connector.



4. INSTALL KNOCK CONTROL SENSOR


    A185819E01
  1. Install the 2 knock sensors with the 2 nuts as shown in the illustration.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the 2 knock sensor connectors.



5. INSTALL VVT SENSOR


A159539
  1. Install the 2 VVT sensors with the 2 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the 2 VVT sensor connectors.



6. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY LH


    A185612
  1. Install a new O-ring to the camshaft timing oil control valve assembly.

  1. Apply a light coat of engine oil to the O-ring.

  1. Install the camshaft timing oil control valve assembly with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the camshaft timing oil control valve assembly connector.



7. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY RH


    A185611
  1. Install a new O-ring to the camshaft timing oil control valve assembly.

  1. Apply a light coat of engine oil to the O-ring.

  1. Install the camshaft timing oil control valve assembly with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the camshaft timing oil control valve assembly connector.



8. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH


    A160775
  1. Install the mounting bracket with the 4 bolts.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }



9. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET RH


    A160774
  1. Install the mounting bracket with the 4 bolts.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }



10. INSTALL FRONT ENGINE MOUNTING INSULATOR LH


    A160788E01
  1. Install the mounting insulator with the nut.

    Torque:
    72 N*m{ 734 kgf*cm , 53 ft.*lbf }



11. INSTALL FRONT ENGINE MOUNTING INSULATOR RH


    A160787E01
  1. Install the mounting insulator with the nut.

    Torque:
    72 N*m{ 734 kgf*cm , 53 ft.*lbf }



12. INSTALL NO. 2 WIRING HARNESS HEAT INSULATOR


    A160781
  1. Install the heat insulator with the 2 bolts.

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }



13. INSTALL OIL COOLER PIPE


    A108784E05
  1. Connect the 3 water by-pass hoses.

  1. Install the oil cooler pipe with the cap nut and bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



14. INSTALL REAR WATER BY-PASS JOINT


    A185674
  1. Remove the 4 nuts and remove the rear water by-pass joint.



    A185675
  1. Remove the 2 gaskets from the cylinder head.



15. INSTALL FRONT WATER BY-PASS JOINT


A115096
  1. Install 2 new gaskets and the water by-pass joint with the 4 nuts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



16. INSTALL INLET WATER HOUSING


    A122973
  1. Disconnect the water by-pass hose from the inlet water housing.

  1. Remove the 2 bolts and inlet water housing with water inlet.

  1. Remove the O-ring from the inlet water housing.



17. INSTALL STARTER ASSEMBLY


    A164438
  1. Remove the 2 bolts holding the starter to the cylinder block.

  1. Disconnect the starter from the cylinder block.



    A164439
  1. Remove the bolt and disconnect the engine wire protector from the starter assembly.

  1. Remove the bolt and ground wire.

  1. Disconnect the starter assembly connector.

  1. Remove the nut and disconnect the starter assembly wire.

  1. Remove the starter assembly.



18. INSTALL NO. 4 AIR INJECTION SYSTEM HOSE


    A185661
  1. Loosen the 2 clips and remove the No. 1 air injection system hose.



19. INSTALL AIR PUMP ASSEMBLY


    A153499
  1. Remove the bolt, 2 nuts and air pump assembly.



20. INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY
  1. Install a new O-ring to the water by-pass pipe sub-assembly.

  1. Apply soapy water to the O-ring.



    A162643
  1. Push in the water by-pass pipe sub-assembly.

  1. Connect the water by-pass pipe sub-assembly with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Connect the connector clamp.



21. INSTALL AIR TUBE


    A153517E01
  1. Install the gasket and air tube with the 3 bolts.

    1. for bolt A

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    1. for bolt B

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }



22. INSTALL INTAKE MANIFOLD


    A156181
  1. Place 2 new gaskets on the intake manifold assembly.

  1. Place the intake manifold assembly on the cylinder heads.



    A156172
  1. Install and uniformly tighten the 6 bolts and 4 nuts in several steps.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



    A156173
  1. Install the engine wire protector with the 2 bolts.

    Torque:
    8.2 N*m{ 83 kgf*cm , 72 in.*lbf }

  1. Connect the 8 injector connectors.



    A163553
  1. Connect the 2 wire clamps.



    A166384
  1. Connect the vacuum switching valve assembly (for ACIS) connector.



    A166385
  1. Install the wire harness bracket to the intake manifold assembly with the bolt.

    Torque:
    8.2 N*m{ 83 kgf*cm , 72 in.*lbf }


    1. Connect the wire harness clamp to the engine hanger.



    A156171
  1. Connect the purge line hose to the purge VSV.

  1. Connect the purge VSV connector.



    A166383
  1. Install the No. 1 ventilation hose with the 2 clamps.



    A156170
  1. Connect the 2 water by-pass hoses to the throttle body assembly.

  1. Connect the throttle body assembly connector.



23. INSTALL NO. 3 WATER BY-PASS PIPE


    A156177
  1. Connect the 2 water hoses to the No. 2 water by-pass pipe.

  1. Install the No. 2 water by-pass pipe with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



    A156176
  1. Connect the 2 water hoses to the No. 2 water by-pass pipe.



24. INSTALL VACUUM HOSE ASSEMBLY


    A156175
  1. Connect the vacuum hose assembly to the intake manifold assembly.

  1. Install the vacuum hose assembly with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



25. INSTALL IGNITION COIL ASSEMBLY


    A156195
  1. Install the 8 ignition coil assemblies with the 8 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the 8 ignition coil assembly connectors.



26. INSTALL AIR SWITCHING VALVE ASSEMBLY (for Bank 2)


    A153513E01
  1. Install the air switching valve assembly with the 3 nuts.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }

    NOTICE:
    Do not hold the bracket of the air switching valve assembly.



27. INSTALL NO. 2 AIR TUBE HOSE


    A153510
  1. Disconnect the air switching valve assembly connector.

  1. Disconnect the wire harness clamp.



    A153512
  1. Remove the 4 nuts, No. 2 air tube and 2 gaskets.

    NOTICE:
    Be careful not to damage the installation surface of the gaskets.



28. INSTALL AIR SWITCHING VALVE ASSEMBLY (for Bank 1)


A153519E01
  1. Install the air switching valve assembly with the 3 nuts.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }

    NOTICE:
    Do not hold the bracket of the air switching valve assembly.