Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK MAIN BODY ECU

B174142E05

  1. Disconnect the DD, H2, H3 and H4 main body ECU connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    DD-62 (GND1, GND2) - Body ground
    W-B - Body ground
    Body ground
    Always
    Below 1 Ω
    H2-4 (HAZ) - Body ground
    O - Body ground
    Hazard warning signal switch input signal
    Hazard warning signal switch OFF → ON
    10 kΩ or higher → Below 1 Ω
    H3-28 (FFOG) - Body ground
    P - Body ground
    Front fog light switch signal
    Front fog light switch OFF → ON
    10 kΩ or higher → Below 1 Ω
    H3-17 (HEAD) - Body ground
    W - Body ground
    Light control switch HEAD signal
    Light control switch HEAD
    Below 1 Ω
    Light control switch except HEAD
    10 kΩ or higher
    H3-21 (PCTY) - Body ground
    O - Body ground
    Front door courtesy light switch RH signal
    Front door RH open → closed
    Below 1 Ω → 10 kΩ or higher
    H4-21 (A) - Body ground
    G - Body ground
    Light control switch AUTO signal
    Light control switch AUTO
    Below 1 Ω
    Light control switch except AUTO
    10 kΩ or higher
    H4-23 (TAIL) - Body ground
    O - Body ground
    Light control switch TAIL signal
    Light control switch TAIL
    Below 1 Ω
    Light control switch except TAIL
    10 kΩ or higher
    H4-24 (DCTY) - Body ground
    BR - Body ground
    Front door courtesy light switch LH signal
    Front door LH open → closed
    Below 1 Ω → 10 kΩ or higher
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the DD, H2, H3, and H4 main body ECU connectors.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    DB-13 (BECU) - Body ground
    GR - Body ground
    BECU power supply
    Always
    11 to 14 V
    DB-16 (DIM) - Body ground
    R - Body ground
    Headlight low beam signal
    Light control switch HEAD,
    dimmer switch High
    Below 1 V
    Light control switch HEAD,
    dimmer switch except High
    11 to 14 V
    DB-18 (HRLY) - Body ground
    L - Body ground
    Headlight low beam signal
    Light control switch HEAD,
    dimmer switch Low
    Below 1 V
    Light control switch HEAD,
    dimmer switch except Low
    11 to 14 V
    H2-5 (CANH) - DD-62 (GND1, GND2)
    L - W-B
    CAN communication signal
    Ignition switch ON
    Pulse generation
    (See waveform 1)
    H2-6 (CANL) - DD-62 (GND1, GND2)
    W - W-B
    CAN communication signal
    Ignition switch ON
    Pulse generation
    (See waveform 2)
    H4-4 (FFGO) - Body ground
    SB - Body ground
    Front fog light signal
    Light control switch TAIL,
    front fog light switch ON
    Below 1 V
    Light control switch TAIL,
    front fog light switch OFF
    11 to 14 V
    If the result is not as specified, the main body ECU may have a malfunction.



  5. A086154E10
  6. Waveform 1 (Reference) : Using an oscilloscope
    CAN Communication Signal 
    Terminal Name
    CANH - GND1, GND2
    Tester Range
    1 V/DIV., 10 μsec./DIV.
    Condition
    Ignition switch ON

    HINT:
    The waveform varies depending on the CAN communication signal.



  7. A086155E11
  8. Waveform 2 (Reference) : Using an oscilloscope
    CAN Communication Signal 
    Terminal Name
    CANL - GND1, GND2
    Tester Range
    1 V/DIV., 10 μsec./DIV.
    Condition
    Ignition switch ON

    HINT:
    The waveform varies depending on the CAN communication signal.


CHECK OUTER MIRROR CONTROL ECU

B166573E07

  1. Disconnect the M7 and M8 outer mirror control ECU connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    M7-3 (B) - Body ground
    R - Body ground
    Battery power supply
    Always
    11 to 14 V
    M7-4 (ACC) - Body ground
    Y - Body ground
    ACC power supply
    Ignition switch
    off → ACC
    Below 1 V → 11 to 14 V
    M7-9 (GND) - Body ground
    W-B - Body ground
    Body ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the M7 and M8 outer mirror control ECU connectors.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    M8-1 (CAN) - M7-9 (GND)
    LG - W-B
    CAN communication signal
    Ignition switch ON
    Pulse generation
    (see waveform 1)
    M8-17 (LP) - Body ground
    V - Body ground
    Puddle light LH operation signal
    Puddle light LH turn on
    11 to 14 V
    M8-21 (CGND) - M7-9 (GND)
    W - W-B
    CAN communication signal
    Ignition switch ON
    Pulse generation
    (see waveform 2)
    M8-37 (LP) - Body ground
    SB - Body ground
    Puddle light RH operation signal
    Puddle light RH turn on
    11 to 14 V
    If the result is not as specified, the ECU may have a malfunction.



  5. A086154E10
  6. Waveform 1 (Reference) : Using an oscilloscope
    CAN Communication Signal 
    Terminal Name
    CAN - GND
    Tester Range
    1 V/DIV., 10 μsec./DIV.
    Condition
    Ignition switch ON

    HINT:
    The waveform varies depending on the CAN communication signal.



  7. A086155E11
  8. Waveform 2 (Reference) : Using an oscilloscope
    CAN Communication Signal 
    Terminal Name
    CGND - GND
    Tester Range
    1 V/DIV., 10 μsec./DIV.
    Condition
    Ignition switch ON

    HINT:
    The waveform varies depending on the CAN communication signal.