LIGHTING SYSTEM > Light Control Switch Circuit |

| 1.READ VALUE USING TECHSTREAM (HEADLIGHT DIMMER SWITCH) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Body Electrical / Main Body / Data List /
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Dimmer SW | Dimmer switch signal / ON or OFF | ON: Dimmer switch ON OFF: Dimmer switch OFF | - |
| Passing Light SW | Passing light switch signal / ON or OFF | ON: Passing light switch ON OFF: Passing light switch OFF | - |
| Front Fog Light SW | Front fog light switch signal / ON or OFF | ON: Front fog light switch ON OFF: Front fog light switch OFF | - |
| Auto Light SW | Auto light switch signal / ON or OFF | ON: Auto light switch ON OFF: Auto light switch OFF | - |
| Head Light SW (Head) | Headlight switch signal / ON or OFF | ON: Headlight switch ON OFF: Headlight switch OFF | - |
| Head Light SW (Tail) | Taillight switch signal / ON or OFF | ON: Taillight switch ON OFF: Taillight switch OFF | - |
|
| ||||
| OK | ||
| ||
| 2.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY |
![]() |
Remove the headlight dimmer switch assembly (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 18 (T) - 12 (EL) | Light control switch TAIL | Below 1 Ω |
| Light control switch HEAD | Below 1 Ω | |
| 20 (H) - 12 (EL) | Light control switch HEAD | Below 1 Ω |
| 19 (A) - 12 (EL) | Light control switch AUTO | Below 1 Ω |
| 4 (BFG) - 3 (LFG) | Front fog light switch ON | Below 1 Ω |
| 17 (HF) - 12 (EL) | Dimmer switch High | Below 1 Ω |
| 11 (HU) - 12 (EL) | Dimmer switch Low | Below 1 Ω |
Reinstall the headlight dimmer switch assembly.
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER SWITCH ASSEMBLY - MAIN BODY ECU) |
![]() |
Disconnect the H11 headlight dimmer switch assembly connector.
Disconnect the H3, H4 and DD main body ECU connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H11-4 (BFG) - H3-28 (FFOG) | Always | Below 1 Ω |
| H11-19 (A) - H4-21 (A) | Always | Below 1 Ω |
| H11-20 (H) - H3-17 (HEAD) | Always | Below 1 Ω |
| H11-18 (T) - H4-23 (TAIL) | Always | Below 1 Ω |
| H11-17 (HF) - H4-13 (HF) | Always | Below 1 Ω |
| H11-11 (HU) - DD-13 (HU) | Always | Below 1 Ω |
| H11-4 (BFG) - Body ground | Always | 10 kΩ or higher |
| H11-19 (A) - Body ground | Always | 10 kΩ or higher |
| H11-20 (H) - Body ground | Always | 10 kΩ or higher |
| H11-18 (T) - Body ground | Always | 10 kΩ or higher |
| H11-17 (HF) - Body ground | Always | 10 kΩ or higher |
| H11-11 (HU) - Body ground | Always | 10 kΩ or higher |
Reconnect the main body ECU connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H11-12 (EL) - Body ground | Always | Below 1 Ω |
| H11-3 (LFG) - Body ground | Always | Below 1 Ω |
Reconnect the headlight dimmer switch assembly connector.
|
| ||||
| OK | ||
| ||