LIGHTING SYSTEM > Headlight Signal Circuit |

| 1.PERFORM ACTIVE TEST USING TECHSTREAM (HEADLIGHT) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Body Electrical / Main Body / Active Test / Headlight Relay
Check that the headlight (low) turn on/off.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Headlight Relay | Headlight | ON or OFF | - |
|
| ||||
| OK | ||
| ||
| 2.INSPECT FUSE (HEAD LL, HEAD RL) |
![]() |
Remove the HEAD LL and HEAD RL fuses from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| HEAD LL fuse | Always | Below 1 Ω |
| HEAD RL fuse | Always | Below 1 Ω |
Reinstall the HEAD LL and HEAD RL fuses.
|
| ||||
| OK | |
| 3.INSPECT HEADLIGHT (LOW) BULB |
Temporarily replace the headlight (low) bulb with a new or normally functioning one .
Check that the headlight (low) turn on.
|
| ||||
| OK | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (HEADLIGHT LOW BULB - HEAD RELAY) |
![]() |
for LH:
Disconnect the A12 headlight (low) LH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A12-2 - Body ground | Light control switch HEAD, dimmer switch Low | 11 to 14 V |
| Light control switch HEAD, dimmer switch except Low | Below 1 V |
Reinstall the headlight (low) LH connector.
for RH:
Disconnect the A13 headlight (low) RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A13-2 - Body ground | Light control switch HEAD, dimmer switch Low | 11 to 14 V |
| Light control switch HEAD, dimmer switch except Low | Below 1 V |
Reinstall the headlight (low) RH connector.
|
| ||||
| OK | ||
| ||
| 5.INSPECT HEADLIGHT RELAY (HEAD) |
![]() |
Remove the HEAD relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 5 | When battery voltage is not applied to terminals 1 and 2 | 10 kΩ or higher |
| When battery voltage is applied to terminals 1 and 2 | Below 1 Ω |
Reinstall the HEAD relay.
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (HEAD RELAY - BATTERY) |
![]() |
Remove the HEAD relay from the engine room relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| HEAD relay terminal 1 - Body ground | Always | 11 to 14 V |
| HEAD relay terminal 3 - Body ground | Always | 11 to 14 V |
Reinstall the HEAD relay.
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (HEAD RELAY - HEADLIGHT LOW BULB) |
![]() |
Remove the HEAD relay from the engine room relay block.
for LH:
Disconnect the A12 headlight (low) LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| HEAD relay terminal 5 - A12-2 | Always | Below 1 Ω |
| HEAD relay terminal 5 - Body ground | Always | 10 kΩ or higher |
Reinstall the headlight (low) LH connector.
for RH:
Disconnect the A13 headlight (low) RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| HEAD relay terminal 5 - A13-2 | Always | Below 1 Ω |
| HEAD relay terminal 5 - Body ground | Always | 10 kΩ or higher |
Reinstall the headlight (low) RH connector.
Reinstall the HEAD relay.
|
| ||||
| OK | |
| 8.CHECK HEADLIGHT (HEADLIGHT RELAY - MAIN BODY ECU) |
![]() |
Disconnect the DB main body ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| DB-18 - Body ground | Always | 11 to 14 V |
Reconnect the main body ECU connector.
|
| ||||
| OK | ||
| ||