LIGHTING SYSTEM > Headlight (HI-BEAM) Circuit |

| 1.PERFORM ACTIVE TEST USING TECHSTREAM (HEADLIGHT (HIGH)) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Body Electrical / Main Body / Active Test / Head Light Hi
Check that the headlight (high) turns on/off.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Head Light Hi | Headlight (High) | ON or OFF | - |
|
| ||||
| OK | ||
| ||
| 2.INSPECT FUSE (HEAD LH, HEAD RH) |
![]() |
Remove the HEAD LH and HEAD RH fuse from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| HEAD LH fuse | Always | Below 1 Ω |
| HEAD RH fuse | Always | Below 1 Ω |
Reinstall the HEAD LH and HEAD RH fuses.
|
| ||||
| OK | |
| 3.INSPECT HEADLIGHT (HIGH) BULB |
Temporarily replace the headlight (high) bulb with a new or normally functioning one .
Check that the headlight (high) come on.
|
| ||||
| OK | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (HEADLIGHT (HIGH) BULB - HEADLIGHT DIMMER RELAY) |
![]() |
for LH:
Disconnect the A10 headlight (high) LH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A10-2 - Body ground | Light control switch HEAD, dimmer switch High | 11 to 14 V |
| Light control switch HEAD, dimmer switch except High | Below 1 V |
Reconnect the headlight (high) LH connector.
for RH:
Disconnect the A11 headlight (high) RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A11-2 - Body ground | Light control switch HEAD, dimmer switch High | 11 to 14 V |
| Light control switch HEAD, dimmer switch except High | Below 1 V |
Reconnect the headlight (high) RH connector.
|
| ||||
| OK | ||
| ||
| 5.INSPECT HEADLIGHT DIMMER RELAY (DIM) |
![]() |
Remove the DIM relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 5 | When battery voltage is not applied to terminals 1 and 2 | 10 kΩ or higher |
| When battery voltage is applied to terminals 1 and 2 | Below 1 Ω |
Reinstall the DIM relay.
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (DIM RELAY - HEAD RELAY) |
![]() |
Remove the DIM relay from the engine room relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| DIM relay terminal 1 - Body ground | Light control switch HEAD, dimmer switch Low | 11 to 14 V |
| DIM relay terminal 3 - Body ground | Light control switch HEAD, dimmer switch Low | 11 to 14 V |
Reinstall the DIM relay.
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (DIM RELAY - HEADLIGHT (HIGH) BULB) |
![]() |
Remove the DIM relay from the engine room relay block.
for LH:
Disconnect the A10 headlight (high) LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| DIM relay terminal 5 - A10-2 | Always | Below 1 Ω |
| DIM relay terminal 5 - Body ground | Always | 10 kΩ or higher |
Reconnect the headlight (high) LH connector.
for RH:
Disconnect the A11 headlight (high) RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| DIM relay terminal 5 - A11-2 | Always | Below 1 Ω |
| DIM relay terminal 5 - Body ground | Always | 10 kΩ or higher |
Reconnect the headlight (high) RH connector.
Reinstall the DIM relay.
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (DIM RELAY - MAIN BODY ECU) |
![]() |
Disconnect the DB main body ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| DB-16 - Body ground | Light control switch HEAD | 11 to 14 V |
Reconnect the main body ECU connector.
|
| ||||
| OK | ||
| ||