FRONT SEAT ASSEMBLY (for Power Seat) > DISASSEMBLY |
| 1. REMOVE OCCUPANT CLASSIFICATION ECU (for Front Passenger Side) |
![]() |
Disconnect the 2 connectors from the occupant classification ECU.
Disengage the claw and occupant classification ECU.
| 2. REMOVE SEAT POSITION AIRBAG SENSOR (for Driver Side) |
![]() |
Disconnect the connector from the seat position airbag sensor.
Using "TORX" socket wrench T30, remove the "TORX" screw and the seat position airbag sensor.
Remove the seat slide position sensor protector from the seat position airbag sensor.
| 3. REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB |
![]() |
Apply protective tape around the cushion shield.
Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the knob.
| 4. REMOVE RECLINING POWER SEAT SWITCH KNOB |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the knob.
| 5. REMOVE FRONT SEAT CUSHION SHIELD LH |
![]() |
Remove the hog rings and rubber bands of the seatback cover from the seat frame.
Remove the 2 screws.
![]() |
Remove the 3 screws.
Disengage the 2 claws and remove the cushion shield.
Disconnect the connectors.
| 6. REMOVE FRONT POWER SEAT LUMBAR SWITCH |
![]() |
Disconnect the connector.
Remove the 2 screws and front power seat lumbar switch.
| 7. REMOVE LEG SUPPORT ADJUSTMENT SWITCH (w/ Leg Support Adjustment Switch) |
![]() |
Disengage the 2 wire harness clamps.
Remove the 2 screws and leg support adjustment switch.
Disconnect the connector.
| 8. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH |
![]() |
Disconnect the connector and disengage the 5 clamps.
![]() |
Remove the nut and front seat inner belt LH.
| 9. REMOVE FRONT SEAT CUSHION SHIELD INNER LH |
![]() |
Remove the screw.
Disengage the 2 claws and clip, and then remove the cushion shield.
| 10. REMOVE FRONT POWER SEAT SWITCH LH |
![]() |
Disconnect the connectors.
Remove the 3 screws and switch.
| 11. REMOVE SEAT CUSHION COVER WITH PAD (w/ Leg Support Adjustment Switch) |
![]() |
Using a clip remover, remove the 2 clips.
![]() |
Disconnect the connector and disengage the 2 wire harness clamps.
![]() |
Disconnect the connector and disengage the 2 wire harness clamps.
![]() |
Remove the 4 hog rings and disengage the hooks.
![]() |
Remove the seat cushion cover wire.
Remove the seat cushion cover with pad from the seat frame.
| 12. REMOVE SEAT CUSHION COVER WITH PAD (w/o Leg Support Adjustment Switch) |
![]() |
Using a clip remover, remove the 2 clips.
![]() |
Disconnect the connector and disengage the 2 wire harness clamps.
![]() |
Disconnect the connector and disengage the 2 wire harness clamps.
![]() |
Remove the 2 hog rings.
Bend the 2 seat frame claws upward.
Disengage the hooks and remove the seat cushion cover with pad.
| 13. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER (w/ Leg Support Adjustment Switch) |
Remove the 15 hog rings and front seat cushion cover.

| 14. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER (w/o Leg Support Adjustment Switch) |
![]() |
Remove the 10 hog rings and front seat cushion cover.
| 15. REMOVE FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System) |
![]() |
Cut off the 30 tack pins which fasten the seat heater to the seat cushion cover, and then remove the seat cushion heater from the seat cushion cover.
| 16. REMOVE FRONT SEAT HEADREST SUPPORT |
![]() |
Remove the 3 hog rings.
![]() |
Disengage the hook.
![]() |
Remove the 2 hog rings and seatback cover wires.
![]() |
Disengage the 4 claws and remove the 2 headrest supports.
| 17. REMOVE SEATBACK COVER WITH PAD |
![]() |
Lift the seatback cover and remove the nut and seatback cover bracket from the seat frame.
Lift the seatback cover and remove the 4 hog rings and seatback cover with pad.
| 18. REMOVE SEPARATE TYPE FRONT SEATBACK COVER |
![]() |
Remove the 2 hog rings and seatback cover wires.
![]() |
Disconnect the seatback cover bracket from the seatback pad.
![]() |
Remove the 2 hog rings and seatback cover from the seatback pad.
| 19. REMOVE FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System) |
![]() |
Cut off the 9 tack pins which fasten the seatback heater to the seatback cover, and then remove the seatback heater from the seatback cover.
| 20. REMOVE RECLINING ADJUSTER INSIDE COVER LH |
![]() |
Remove the screw.
Disengage the claw and remove the reclining adjuster inside cover.
| 21. REMOVE RECLINING ADJUSTER INSIDE COVER RH |
| 22. REMOVE FRONT SEATBACK SHIELD LH |
![]() |
Remove the 2 screws.
Disengage the claw and remove the front seatback shield.
| 23. REMOVE FRONT SEATBACK SHIELD RH |
![]() |
Disengage the wire harness clamp.
Remove the 2 screws.
Disengage the claw and remove the front seatback shield.
| 24. REMOVE FRONT SEAT CUSHION SHIELD SUB-ASSEMBLY LH NO. 2 |
![]() |
Remove the screw.
Disengage the hook and remove the cushion shield.
| 25. REMOVE FRONT SEAT CUSHION SHIELD SUB-ASSEMBLY LH NO. 1 |
| 26. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/ Climate Control Seat System) |
![]() |
Disconnect the connector and disengage the 2 clamps.
![]() |
Remove the 4 springs.
Disengage the 4 hooks and remove the seatback spring.
![]() |
Disconnect the connector.
Remove the 2 screws and lumbar support adjuster assembly.
![]() |
Disengage the 3 claws and remove the bush from the seat frame.
| 27. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/o Climate Control Seat System) |
![]() |
Remove the 2 springs.
Detach the 6 hooks and remove the seatback spring.
![]() |
Disconnect the connector.
Remove the 2 screws and lumbar support adjuster assembly.
![]() |
Disengage the 3 claws and remove the bush from the seat frame.
| 28. REMOVE SEATBACK CLIMATE CONTROL COVER LH NO. 1 (w/ Climate Control Seat System) |
![]() |
Using a T30 "TORX" socket, remove the 4 screws and then remove the seatback climate control cover LH No. 1.
| 29. REMOVE SEATBACK CLIMATE CONTROL BLOWER LH (w/ Climate Control Seat System) |
![]() |
Disengage the clamp.
Using a T30 "TORX" socket, remove the 2 screws and then remove the seatback climate control blower LH and seatback climate control cover LH No. 3.
| 30. REMOVE SEATBACK CLIMATE CONTROL COVER LH NO. 2 (w/ Climate Control Seat System) |
![]() |
Disengage the 6 clamps and remove the seatback climate control cover LH No. 2.
| 31. REMOVE SEAT CUSHION CLIMATE CONTROL DUCT LH (w/ Climate Control Seat System) |
![]() |
Separate the 2 clamps (A) in the direction indicated by the arrow (1).
Separate the 2 clamps (B) in the direction indicated by the arrow (2).
Disengage the 2 claws, and remove the seat cushion climate control duct LH.
| 32. REMOVE SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY (w/ Climate Control Seat System) |
![]() |
Disconnect the connector.
Using a T30 "TORX" socket, remove the screw.
Bend the bracket open slightly.
Disengage the 2 claws and remove the seat cushion climate control blower by pushing it rearward.
| 33. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System) |
![]() |
Disconnect the seat heater control connector and disengage the clamp.
Disengage the clamp and remove the seat heater control.
| 34. REMOVE FRONT SEAT WIRE LH (for Driver Side) |
![]() |
Disconnect the 3 connectors.
Disengage the 6 wire harness clamps.
| 35. REMOVE FRONT SEAT WIRE RH (for Front Passenger Side) |
![]() |
Disconnect the 5 connectors.
Disengage the 7 wire harness clamps.