Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (for Power Seat)

FRONT SEAT ASSEMBLY (for Power Seat) > REASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.

HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The procedures listed below is for the LH side.



1. INSTALL FRONT SEAT WIRE LH (for Driver Side)


    B191030
  1. Connect the 3 connectors and engage the 6 wire harness clamps.



2. INSTALL FRONT SEAT WIRE RH (for Front Passenger Side)


    B191031
  1. Connect the 5 connectors and engage the 7 wire harness clamps.



3. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System)


    B191029
  1. Engage the clamp to install the seat heater control.

  1. Engage the clamp and connect the connector.



4. INSTALL SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY (w/ Climate Control Seat System)


    B146608E04
  1. Engage the 2 claws and install the seat cushion climate control blower by pushing it forward.

  1. Bend the bracket closed.

  1. Using a T30 "TORX" socket, install the screw.

    Torque:
    2.6 N*m{ 27 kgf*cm , 23 in.*lbf }

  1. Connect the connector.



5. INSTALL SEAT CUSHION CLIMATE CONTROL DUCT LH (w/ Climate Control Seat System)


    B201573E01
  1. Engage the 2 claws to install the seat cushion climate control duct.

  1. Engage the 2 clamps (B).

  1. Engage the 2 clamps (A).



6. INSTALL SEATBACK CLIMATE CONTROL COVER LH NO. 2 (w/ Climate Control Seat System)


    B194062
  1. Engage the 6 clamps and install the seatback climate control cover LH No. 2.



7. INSTALL SEATBACK CLIMATE CONTROL BLOWER LH (w/ Climate Control Seat System)


B194060
  1. Install the seatback climate control cover LH No. 3.

  1. Using a T30 "TORX" socket, install the seatback climate control blower with the 2 screws.

  1. Engage the connector.



8. INSTALL SEATBACK CLIMATE CONTROL COVER LH NO. 1 (w/ Climate Control Seat System)


    B194061
  1. Using a T30 "TORX" socket, install the seatback climate control cover LH No. 1 with the 4 screws.



9. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/ Climate Control Seat System)


    B167110
  1. Engage the 3 claws to install the bush.



    B200258
  1. Install the lumbar support adjuster assembly with the 2 screws.

  1. Connect the connector.



    B194042E01
  1. Engage the 4 hooks to install the seatback spring.

  1. Install the 4 springs.



    B195621
  1. Engage the 2 clamps and connect the connector.



10. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/o Climate Control Seat System)


    B167110
  1. Attach the 3 claws to install the bush.



    B200258
  1. Install the lumbar support adjuster with the 2 screws.

  1. Connect the lumbar support adjuster connector.



    B191028E01
  1. Engage the 6 hooks to install the seatback spring.



11. INSTALL FRONT SEAT CUSHION SHIELD SUB-ASSEMBLY LH NO. 2


    B201571
  1. Engage the hook to install the cushion shield.

  1. Install the screw.



12. INSTALL FRONT SEAT CUSHION SHIELD SUB-ASSEMBLY LH NO. 1

HINT:
Use the same procedure for the LH side and RH side.



13. INSTALL FRONT SEATBACK SHIELD LH


    B201570
  1. Engage the claw to install the seatback shield.

  1. Install the 2 screws.



14. INSTALL FRONT SEATBACK SHIELD RH


    B191027
  1. Engage the claw to install the seatback shield.

  1. Install the 2 screws.

  1. Engage the wire harness clamp.



15. INSTALL RECLINING ADJUSTER INSIDE COVER LH


    B201569
  1. Engage the claw to install the reclining adjuster inside cover.

  1. Install the screw.



16. INSTALL RECLINING ADJUSTER INSIDE COVER RH

HINT:
Use the same procedure for the LH side and RH side.



17. INSTALL FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System)


    B194830
  1. Set the seatback heater with the name stamp side facing the seatback cover.

  1. Install the seatback heater with new 9 tack pins.



18. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    B191032E01
  1. Using hog ring pliers, install the seatback cover to the seatback pad with 2 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



    B166411
  1. Connect the seatback cover bracket to the seatback pad.



    B194827E01
  1. Install the seatback cover wires.

  1. Using hog ring pliers, install 2 new hog rings to the seatback pad.



19. INSTALL SEATBACK COVER WITH PAD


    B194821E02
  1. Install the seatback cover with pad to the seatback frame.

  1. Lift the seatback cover and, using hog ring pliers, install 4 new hog rings to the seat frame.

  1. lift the seatback cover, connect the seatback cover bracket to the seat frame, and install the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    CAUTION:
    After the seatback trim cover is assembled, make sure that the side airbag strap is not twisted.



    B194828E01
  1. Install the seatback cover wires.

  1. Using hog ring pliers, install 2 new hog rings to the seat frame.



    B191023
  1. Engage the hooks.



    B194829E01
  1. Using hog ring pliers, install 3 new hog rings to the seat frame.



20. INSTALL FRONT SEAT HEADREST SUPPORT


    B191062E04
  1. Align the protruding portion of the front seat headrest supports with the installation grooves of the front seatback frame.

  1. Engage the 4 claws to install the 2 headrest supports.



21. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System)


    B194831
  1. Set the seat cushion heater with the name stamp side facing the seat cushion cover.

  1. Install the seat cushion heater with new 30 tack pins.



22. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER (w/ Leg Support Adjustment Switch)


  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 15 new hog rings.


    B191035E01

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



23. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER (w/o Leg Support Adjustment Switch)


    B191036E01
  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 10 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



24. INSTALL SEAT CUSHION COVER WITH PAD (w/ Leg Support Adjustment Switch)


    B167190
  1. Install the seat cushion cover with pad to the seat frame.

  1. Install the seat cushion cover wire.



    B195224E01
  1. Using hog ring pliers, install 4 new hog rings and attach the hooks.

    HINT:
    When installing the leg support hog rings, press the seat cushion cover with pad against the seat frame.



    B191017
  1. Connect the connector and engage the 2 wire harness clamps.



    B191016E01
  1. Connect the connector and engage the 2 wire harness clamps.



    B167097
  1. Install the 2 clips.



25. INSTALL SEAT CUSHION COVER WITH PAD (w/o Leg Support Adjustment Switch)


    B195225E01
  1. Engage the hooks to install the seat cushion cover with pad.

  1. Using hog ring pliers, install 2 new hog rings.

  1. Bend the 2 seat frame claws downward.



    B194826
  1. Connect the connector and engage the 2 wire harness clamps.



    B194825
  1. Connect the connector and engage the 2 wire harness clamps.



    B167097
  1. Install the 2 clips.



26. INSTALL FRONT POWER SEAT SWITCH LH


    B166949
  1. Install the switch with the 3 screws.

  1. Connect the connectors.



27. INSTALL FRONT SEAT CUSHION SHIELD INNER LH


B191015
  1. Engage the 2 claws and clip to install the cushion shield.

  1. Install the screw.



28. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH


    B191260E01
  1. Install the front seat inner belt LH with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt to overlap the protruding part of the front seat adjuster.



    B191250
  1. Connect the connector and engage the 5 clamps.



29. INSTALL LEG SUPPORT ADJUSTMENT SWITCH (w/ Leg Support Adjustment Switch)


    B191014
  1. Connect the connector.

  1. Install the leg support adjustment switch with the 2 screws.

  1. Engage the 2 wire harness clamps.



30. INSTALL FRONT POWER SEAT LUMBAR SWITCH


    B201589
  1. Install the front power seat lumbar switch with the 2 screws.

  1. Connect the connector.



31. INSTALL FRONT SEAT CUSHION SHIELD LH


    B166945
  1. Connect the switch connectors.

  1. Engage the 2 claws to install the cushion shield.

  1. Install the 3 screws.



    B195226E01
  1. Install the 2 screws.

  1. Using hog ring pliers, install the rubber band of the seatback cover to the seat frame with 2 new hog rings.



32. INSTALL RECLINING POWER SEAT SWITCH KNOB


B201574
  1. Engage the 2 claws to install the knob.



33. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


B201575
  1. Engage the 2 claws to install the knob.



34. INSTALL SEAT POSITION AIRBAG SENSOR (for Driver Side)
  1. Check that the ignition switch is turned off.

  1. Check that the battery negative (-) terminal is disconnected.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



    B169961E01
  1. Using an 1 mm (0.039 in.) feeler gauge, install the seat position airbag sensor.

    NOTICE:
    1. If the seat position airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace the seat position airbag sensor with a new one.
    2. When installing the seat position airbag sensor, make sure that the SRS wiring does not interfere with other parts and is not pinched between other parts.

    HINT:
    Maintain a clearance between the seat position airbag sensor and the seat rail of between 0.6 mm (0.023 in.) and 2 mm (0.079 in.).



    B194812E01
  1. Using "TORX" socket wrench, tighten the "TORX" screw to install the seat position airbag sensor.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Make sure that the clearance between the seat position airbag sensor and the seat rail is between 0.6 mm (0.023 in.) and 2 mm (0.079 in.).

  1. Connect the connector to the seat position airbag sensor.

  1. Check that there is no looseness in the installation parts of the seat position airbag sensor.

  1. Engage the pin and install a new seat position sensor protector.



35. INSTALL OCCUPANT CLASSIFICATION ECU (for Front Passenger Side)


    B194816
  1. Check that the ignition switch is off.

  1. Check that the negative battery (-) terminal is disconnected.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Engage the claw and occupant classification ECU.

  1. Connect the 2 connectors to the occupant classification ECU.

    NOTICE:
    1. If the occupant classification ECU has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
    1. When installing the occupant classification ECU, make sure that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.
    1. When replacing the occupant classification ECU, replace the bolt with a new one.