Home › Vehicle Interior › SEAT › REAR SEATBACK HEATER

REAR SEATBACK HEATER > REMOVAL

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The procedure listed below is for the RH side.



1. REMOVE REAR NO. 1 SEAT ASSEMBLY RH
  1. Remove the rear No. 1 seat assembly (Click here).



2. REMOVE RECLINING ADJUSTER KNOB CAP RH


    B191081E01
  1. Using a screwdriver, disengage the 3 claws and remove the reclining adjuster knob cap.

    HINT:
    Tape the screwdriver tip before use.



3. REMOVE REAR SEAT RECLINING RELEASE LEVER


    B191083
  1. Remove the 3 screws and rear seat reclining release lever.



4. REMOVE REAR SEAT CUSHION HINGE COVER NO. 3


B191084
  1. Remove the screw.

  1. Disengage the 2 claws and remove the rear seat cushion hinge cover.



5. REMOVE REAR SEAT CUSHION HINGE COVER NO. 2


B191085
  1. Remove the screw.

  1. Disengage the 2 claws and remove the rear seat cushion hinge cover.



6. REMOVE REAR NO. 1 SEAT CUSHION ASSEMBLY RH


    B191090
  1. Disconnect the connector and disengage the 3 clamps.

    HINT:
    If the vehicle is equipped with the seat heater system, disconnect the connector and disengage the clamps.



    B191088
  1. Cut the cable tie.

  1. Disconnect the cable from the seat cushion spring.



    B191089
  1. Cut the cable tie to remove the cable from the seat cushion spring.

  1. Disengage the cable clamp and remove the cable from the seat cushion spring.



    B200239
  1. Cut the 2 cable ties to remove the cable from the seat cushion spring.



    B191091
  1. Remove the 2 bolts.

  1. Using a T45 "TORX" socket, remove the 2 bolts and 2 bushes. Then remove the rear No. 1 seat cushion assembly.



7. REMOVE NO. 1 SEAT CUSHION COVER RH


    B191122
  1. Disengage the cable clamp and disconnect the cable from the No. 1 seat cushion cover.

  1. Remove the 2 screws.

  1. Disengage the claw and remove the No. 1 seat cushion cover.



8. REMOVE REAR SEAT HEADREST ASSEMBLY


9. REMOVE REAR SEAT BACK BOARD SUB-ASSEMBLY RH


    B191101
  1. Disengage the 7 clips and remove the rear seatback board sub-assembly.



10. REMOVE REAR SEAT CUSHION HINGE COVER NO. 1


    B191095
  1. Remove the screw.

  1. Disengage the 4 claws and clip and remove the rear seat cushion hinge cover.



11. REMOVE REAR SEAT CUSHION HINGE COVER RH


    B191096
  1. Remove the 2 screws.

  1. Disengage the 3 claws and remove the rear seat cushion hinge cover.



12. REMOVE REAR SEAT CUSHION UNDER COVER RH


    B191097
  1. Remove the 3 screws and rear seat cushion under cover.



13. REMOVE REAR SEATBACK LOCK STRIKER COVER


    B191098E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and guide and remove the rear seatback lock striker cover.



14. REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH


    B191100
  1. Remove the 2 screws.

  1. Disconnect the cable and remove the rear seat lock control lever sub-assembly.



15. REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY


    B191133
  1. Disengage the 4 claws and remove the 2 rear seat headrest supports.



16. REMOVE NO. 1 SEATBACK COVER SUB-ASSEMBLY RH


    B200243
  1. Remove the 2 hog rings.

  1. Remove the hooks and No. 1 seatback cover sub-assembly.



17. REMOVE SEATBACK COVER WITH PAD


    B200254
  1. Disengage the harness clamp and disconnect the connector.



    B191102
  1. Remove the 2 hog rings.



    B191104
  1. Disengage the hooks and remove the seatback cover with pad.



18. REMOVE SEPARATE TYPE REAR SEATBACK COVER


    B191106
  1. Remove the 8 hog rings and separate type rear seatback cover from the seatback pad.



19. REMOVE SEATBACK HEATER ASSEMBLY


    B191093
  1. Cut off the tack pins which fasten the seat heater to the seatback cover ,and then remove the seatback heater from the seatback cover.