POWER MIRROR CONTROL SYSTEM (w/ Memory) > DATA LIST / ACTIVE TEST |
| READ DATA LIST |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream ON.
Enter the following menus: Body Electrical or Powertrain / (desired system) / Data List.
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Mirror Selection SW (R) | Mirror master switch signal for RH mirror / ON or OFF | ON: Switch is in R position OFF: Switch is OFF or in L position | - |
| Mirror Selection SW (L) | Mirror master switch signal for LH mirror / ON or OFF | ON: Switch is in L position OFF: Switch is OFF or in R position | - |
| Mirror Position SW (R) | Mirror control switch signal (RIGHT) / ON or OFF | ON: RIGHT switch is ON OFF: Any switch except RIGHT is ON or all switches are OFF | - |
| Mirror Position SW (L) | Mirror control switch signal (LEFT) / ON or OFF | ON: LEFT switch is ON OFF: Any switch except LEFT is ON or all switches are OFF | - |
| Mirror Position SW (UP) | Mirror control switch signal (UP) / ON or OFF | ON: UP switch is ON OFF: Any switch except UP is ON or all switches are OFF | - |
| Mirror Position SW (Dwn) | Mirror control switch signal (DOWN) / ON or OFF | ON: DOWN switch is ON OFF: Any switch except DOWN is ON or all switches are OFF | - |
| Outer Mirror Fold SW | Mirror retract switch signal / ON or OFF | ON: Switch is ON (retracting) OFF: Switch is OFF | - |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Mirror Memory No. 1 | Mirror position memorized in seat memory switch M1 / ON or OFF | ON: Memorized OFF: Not memorized | - |
| Mirror Memory No. 2 | Mirror position memorized in seat memory switch M2 / ON or OFF | ON: Memorized OFF: Not memorized | - |
| RH Mir Position Sensor V | Passenger side mirror vertical sensor voltage / MIN: 0 V, MAX: 5 V | Within range from 0 to 5 V | - |
| RH Mir Position Sensor H | Passenger side mirror horizontal sensor voltage / MIN: 0 V MAX: 5 V | Within range from 0 to 5 V | - |
| LH Mir Position Sensor V | Driver side mirror vertical sensor voltage / MIN: 0 V, MAX: 5 V | Within range from 0 to 5 V | - |
| LH Mir Position Sensor H | Driver side mirror horizontal sensor voltage / MIN: 0 V, MAX: 5 V | Within range from 0 to 5 V | - |
| ACC SW | Ignition switch ACC signal / ON or OFF | ON: Ignition switch ACC OFF: Ignition switch off | - |
| Driver Side SET Mem SW | Driver side seat memory SET switch / ON or OFF | ON: Driver side seat memory SET switch ON OFF: Driver side seat memory SET switch OFF | - |
| Driver Side Memory SW 1 | Driver side seat memory switch 1 / ON or OFF | ON: Driver side seat memory 1 switch ON OFF: Driver side seat memory 1 switch OFF | - |
| Driver Side Memory SW 2 | Driver side seat memory switch 2 / ON or OFF | ON: Driver side seat memory 2 switch ON OFF: Driver side seat memory 2 switch OFF | - |
| Foot Light | Foot light illumination time | OFF/7.5 s/15 s/30 s | - |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Shift SW States (R Range) | PNP switch status / ON or OFF | ON: Shift lever in R OFF Shift lever not in R | - |
| PERFORM ACTIVE TEST |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream ON.
Enter the following menus: Body Electrical / Mirror / Active Test.
According to the display on the Techstream, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| RH Mirror Up/Down | Mirror vertical operation | UP/OFF/DOWN | - |
| RH Mirror Right/Left | Mirror horizontal operation | RIGHT/OFF/LEFT | - |
| LH Mirror Up/Down | Mirror vertical operation | UP/OFF/DOWN | - |
| LH Mirror Right/Left | Mirror horizontal operation | RIGHT/OFF/LEFT | - |
| Foot Light | Foot light illumination operation | ON/OFF | - |
| Mirror Fold | Mirror retract operation | FOLD/OFF | - |
| Mirror Return | Mirror retract operation | RETURN/OFF | - |