Home › Engine / Hybrid System ยท 2UZ-FE › INTAKE / EXHAUST › INTAKE MANIFOLD

INTAKE MANIFOLD > INSTALLATION

for Preparation Click here



1. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

NOTICE:
Be careful not to drop the injectors when installing the delivery pipes.



    A162032E01
  1. Place the 2 delivery pipes and injector assemblies on the lower intake manifold.

  1. Temporarily install the 4 nuts.

  1. Install the No. 1 fuel pipe sub-assembly with the bolt, 4 new gaskets and 2 union bolts.

    1. for union bolt

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }

    1. for bolt

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



    A160921
  1. Install the fuel return pipe with the 3 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



    A160920
  1. Connect the fuel return hose to the fuel pressure regulator.



    A133665E02
  1. Check that the injectors rotate smoothly.

    HINT:
    If the injectors do not rotate smoothly, a probable cause is the incorrect installation of the O-rings. Replace the O-ring of the injector that does not rotate smoothly.

  1. Position the injector connectors outward.

  1. Tighten the 4 nuts holding the delivery pipes to the lower intake manifold.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. Connect the 8 injector connectors.



2. INSTALL VACUUM SWITCHING VALVE ASSEMBLY (for ACIS)


    A166390
  1. Install the vacuum switching valve assembly (for ACIS) with bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the 2 vacuum hose and vacuum switching valve assembly (for ACIS) connector.



3. INSTALL PURGE VSV


    A162052
  1. Install the purge VSV with the bolt to the intake manifold assembly.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Connect the purge line hose to the intake manifold assembly.



4. INSTALL THROTTLE BODY ASSEMBLY


    A156182E01
  1. Align the protrusion of a new gasket with the groove of the intake manifold assembly, and install the gasket.



    A156180E01
  1. Install the throttle body assembly with the nut and 3 bolts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



5. INSTALL INTAKE MANIFOLD ASSEMBLY


    A156181
  1. Place 2 new gaskets on the intake manifold assembly.

  1. Place the intake manifold assembly on the cylinder heads.



    A156172
  1. Install and uniformly tighten the 6 bolts and 4 nuts in several steps.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



    A156173
  1. Install the engine wire protector with the 2 bolts.

    Torque:
    8.2 N*m{ 83 kgf*cm , 72 in.*lbf }

  1. Connect the 8 injector connectors.



    A163553
  1. Connect the 2 wire clamps.



    A166384
  1. Connect the vacuum switching valve assembly (for ACIS) connector.



    A166385
  1. Install the wire harness bracket to the intake manifold assembly with the bolt.

    Torque:
    8.2 N*m{ 83 kgf*cm , 72 in.*lbf }


    1. Connect the wire harness clamp to the engine hanger.



    A156171
  1. Connect the purge line hose to the purge VSV.

  1. Connect the purge VSV connector.



    A166383
  1. Install the No. 1 ventilation hose with the 2 clamps.



    A156170
  1. Connect the 2 water by-pass hoses to the throttle body assembly.

  1. Connect the throttle body assembly connector.



6. INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY


A187100E02
  1. Connect the No. 1 fuel pipe sub-assembly.

    HINT:
    Push the parts together firmly until a "click" sound is heard.

    NOTICE:
    1. Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
    2. After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.



7. INSTALL NO. 2 FUEL PIPE SUB-ASSEMBLY


A160926
  1. Connect the No. 2 fuel pipe sub-assembly (Click here).

    HINT:
    Push the parts together firmly until a "click" sound is heard.

    NOTICE:
    1. Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
    2. After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.



8. INSTALL EFI FUEL PIPE CLAMP


9. INSTALL NO. 2 WATER BY-PASS PIPE


    A156177
  1. Connect the 2 water hoses to the No. 2 water by-pass pipe.

  1. Install the No. 2 water by-pass pipe with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



    A156176
  1. Connect the 2 water hoses to the No. 2 water by-pass pipe.



10. CONNECT VACUUM HOSE ASSEMBLY


    A156175
  1. Connect the vacuum hose assembly to the intake manifold assembly.

  1. Install the vacuum hose assembly with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



11. INSTALL AIR CLEANER HOSE ASSEMBLY


    A153488E02
  1. Install the air cleaner hose assembly with the 2 clamps.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

    HINT:
    Make sure that the clamp band end is aligned with the limit mark when the hose clamp is tightened, as indicated by A and B in the illustration.

  1. Connect the vacuum hose and No. 2 ventilation hose.



12. ADD ENGINE COOLANT
  1. Add engine coolant.

    Standard capacity:
    9.7 liters (10.3 US qts, 8.5 Imp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).
    2. The thermostat opening timing can be confirmed by pressing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.



    A151850E03
  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Install the reservoir cap.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Install the radiator cap.

  1. Start the engine and warm it up until the thermostat opens.

    HINT:
    The thermostat opening timing can be confirmed by pressing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. Maintain the engine speed at 2000 to 2500 rpm and warm up the engine until the cooling fan operates.

    NOTICE:
    1. Make sure that the radiator reservoir still has some coolant in it.
    2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
    3. If there is not enough coolant, the engine may burn out or overheat.

  1. Press the inlet and outlet radiator hoses several times by hand to bleed air.

    CAUTION:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the fan.

  1. Stop the engine, and wait until the engine coolant cools down.



    A151850E04
  1. If the coolant level is below the LOW line, repeat all of the procedures above.



13. INSPECT FOR COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A162054
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop. If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.



14. INSPECT FOR FUEL LEAK
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream ON.

    NOTICE:
    Do not start the engine.

  1. Techstream:
    Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

  1. Check that there are no fuel leaks after doing maintenance anywhere on the fuel system.



    A133618E01
  1. Check that the pulsation damper screw rises up when the fuel pump operates.
    If the operation is not as specified, check the following parts:

    1. Fusible link
    2. Fuses
    3. Circuit opening relay
    4. Fuel pump
    5. ECM
    6. Wiring connections
    If no malfunctions are found in the aforementioned components, replace the pulsation damper.

  1. Turn the ignition switch off.

  1. Disconnect the Techstream from the DLC3.



15. INSTALL NO. 1 ENGINE UNDER COVER


    A150108
  1. Hook the engine under cover onto the vehicle body as shown in the illustration.

  1. Install the 3 screws and 5 bolts.

    1. for bolt

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

    1. for screw

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }



16. INSTALL THROTTLE BODY COVER SUB-ASSEMBLY


    A156184E02
  1. Install the 2 throttle body cover brackets with the 2 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



    A156183E01
  1. Install the throttle body cover sub-assembly with the 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



17. INSTALL FRONT COWL TOP OUTER PANEL SUB-ASSEMBLY


  1. Install the front cowl top outer panel sub-assembly with the 7 bolts.


    A151796

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Install the wire harness clamp to the front cowl top outer panel sub-assembly.

  1. Install the washer hose grommet to the front cowl top outer panel sub-assembly.

  1. Connect the washer hose.



18. INSTALL FRONT WIPER MOTOR AND LINK


    E161316
  1. Install the wiper motor and link assembly with the 4 bolts and nut.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the connector.



19. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E161314
  1. Engage the 6 claws and 8 guides and install the cowl top ventilator louver sub-assembly.

  1. Install the 2 clips.



20. INSTALL FRONT FENDER TO COWL SIDE SEAL RH


    E161313
  1. Engage the claw and install the front fender to cowl side seal.



21. INSTALL FRONT FENDER TO COWL SIDE SEAL LH

HINT:
Use the same procedure for both sides.



22. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E146308E02
  1. Clean any metal powder off the serrated part of the wiper arm with a round wire brush or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, and then stop the wiper motor in the automatic stop position.



    E161321E01
  1. Align the blade tip with the mark on the glass, as shown in the illustration.

    HINT:
    Hold down the wiper arm hinge with your hand while tightening the nut.

  1. Tighten the nut on the front wiper arm and blade.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.



23. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E146308E02
  1. Clean any metal powder off the serrated part of the wiper arm with a round wire brush or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, and then stop the wiper motor in the automatic stop position.



    E161322E01
  1. Align the blade tip with the mark on the glass, as shown in the illustration.

    HINT:
    Hold down the wiper arm hinge with your hand while tightening the nut.

  1. Tighten the nut on the front wiper arm and blade.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.