Home › Engine / Hybrid System ยท 2UZ-FE › INTAKE / EXHAUST › INTAKE MANIFOLD

INTAKE MANIFOLD > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)


2. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E161312
  1. Remove the nut and remove the wiper arm and blade assembly.



3. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

HINT:
Use the same procedure for both sides.



4. REMOVE FRONT FENDER TO COWL SIDE SEAL RH


    E161313
  1. Disengage the claw and remove the front fender to cowl side seal.



5. REMOVE FRONT FENDER TO COWL SIDE SEAL LH

HINT:
Use the same procedure for both sides.



6. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E161315
  1. Remove the 2 clips.

  1. Remove the 6 claws and 8 guides and remove the cowl top ventilator louver sub-assembly.



7. REMOVE FRONT WIPER MOTOR AND LINK ASSEMBLY


    E161316
  1. Disconnect the connector.

  1. Remove the nut.

  1. Remove the 4 bolts and wiper motor and link assembly.



8. REMOVE FRONT COWL TOP OUTER PANEL SUB-ASSEMBLY
  1. Disconnect the washer hose.

  1. Separate the washer hose grommet from the front cowl top outer panel sub-assembly.

  1. Separate the wire harness clamp from the front cowl top outer panel sub-assembly.



  1. Remove the 7 bolts and front cowl top outer panel sub-assembly.


    A151796



9. REMOVE NO. 1 ENGINE UNDER COVER


    A150108
  1. Remove the 3 screws and 5 bolts.

  1. Unhook the engine under cover from the vehicle body as shown in the illustration.



10. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug and 2 cylinder block drain cock plugs.

  1. Remove the radiator cap. Then drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.



  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 10 ft.*lbf }



    A156211E01

  1. Tighten the radiator drain cock plug by hand.



11. REMOVE THROTTLE BODY COVER SUB-ASSEMBLY


    A156183E01
  1. Remove the 2 nuts and throttle body cover sub-assembly.



    A156184E02
  1. Remove the 2 bolts and 2 throttle body cover brackets from the intake manifold.



12. REMOVE AIR CLEANER HOSE ASSEMBLY


    A153487
  1. Disconnect the vacuum hose and No. 2 ventilation hose.

  1. Loosen the 2 hose clamps and remove the air cleaner hose assembly.



13. DISCONNECT VACUUM HOSE ASSEMBLY


    A156175
  1. Remove the bolt and disconnect the vacuum hose assembly.



14. REMOVE NO. 2 WATER BY-PASS PIPE


    A156176
  1. Disconnect the 2 water hoses from the No. 2 water by-pass pipe.



    A156177
  1. Remove the 2 bolts.

  1. Disconnect the 2 water hoses and remove the No. 2 water by-pass pipe.



15. REMOVE EFI FUEL PIPE CLAMP


16. DISCONNECT NO. 2 FUEL PIPE SUB-ASSEMBLY


A185285E01
  1. Disconnect the No. 1 fuel pipe sub-assembly (Click here).

    NOTICE:
    1. Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
    2. Do not use any tools to separate the pipe and connector.
    3. Do not forcefully bend or twist the nylon tube.
    4. Check for foreign matter on the pipe seal surface. Clean if necessary.
    5. Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
    6. If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.



17. DISCONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY


A160926
  1. Disconnect the No. 2 fuel pipe sub-assembly (Click here).

    NOTICE:
    1. Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
    2. Do not use any tools to separate the pipe and connector.
    3. Do not forcefully bend or twist the nylon tube.
    4. Check for foreign matter on the pipe seal surface. Clean if necessary.
    5. Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
    6. If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.



18. REMOVE INTAKE MANIFOLD ASSEMBLY


    A156170
  1. Disconnect the throttle body connector.

  1. Disconnect the 2 water by-pass hoses from the throttle body assembly.



    A166383
  1. Loose the 2 clamps and remove the No. 1 ventilation hose.



    A156171
  1. Disconnect the purge VSV connector.

  1. Disconnect the purge line hose from the purge VSV.



    A166384
  1. Disconnect the vacuum switching valve assembly (for ACIS) connector.



    A166385
  1. Disconnect the wire harness clamp from the engine hanger.

  1. Remove the bolt and wire harness bracket from the intake manifold assembly.



    A163553
  1. Disconnect the 2 wire clamps.

  1. Disconnect the 8 injector connectors.



    A156173
  1. Remove the 2 bolts and separate the engine wire protector.



    A156172
  1. Remove the 6 bolts, 4 nuts, intake manifold assembly and 2 gaskets.



19. REMOVE THROTTLE BODY ASSEMBLY


    A156180E01
  1. Remove the nut, 3 bolts, throttle body assembly and gasket.



20. REMOVE PURGE VSV


    A162052
  1. Disconnect the purge line hose from the intake manifold assembly.

  1. Remove the bolt and purge VSV.



21. REMOVE VACUUM SWITCHING VALVE ASSEMBLY (for ACIS)


    A166390
  1. Disconnect the 2 vacuum hoses and vacuum switching valve assembly (for ACIS) connector.

  1. Remove the bolt and remove the vacuum switching valve assembly (for ACIS).



22. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY


A160920
  1. Disconnect the fuel return hose from the fuel pressure regulator.

    NOTICE:
    Put a cloth or equivalent under the pressure regulator.



    A160921
  1. Remove the 3 bolts and fuel return pipe from the delivery pipe and intake manifold.

    HINT:
    Move the fuel return pipe aside to secure more work space.



    A160927
  1. Remove the bolt, 2 union bolts, 4 gaskets and No. 1 fuel pipe sub-assembly.

  1. Disconnect the 8 injector connectors.

  1. Remove the 4 nuts holding the delivery pipes to the lower intake manifold.

  1. Remove the 2 delivery pipes.

    NOTICE:
    Be careful not to drop the injectors when removing the delivery pipes.