Home › Vehicle Interior › METER / GAUGE / DISPLAY › ACCESSORY METER

ACCESSORY METER > INSTALLATION

for Preparation Click here



1. INSTALL ACCESSORY METER ASSEMBLY


    B160594
  1. Install the accessory meter with the 3 screws.

  1. Connect the connector.



2. INSTALL NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY


B192357
  1. Install the register with the 3 <G> screws.



3. INSTALL DEFROSTER NOZZLE ASSEMBLY


B192355
  1. Install the defroster nozzle with the 3 <G> screws.



4. INSTALL NO. 2 SIDE DEFROSTER NOZZLE DUCT


B192354
  1. Engage the 2 claws and install the duct.

  1. Install the 2 <G> screws.



5. INSTALL NO. 1 SIDE DEFROSTER NOZZLE DUCT


B192353
  1. Engage the 2 claws and install the duct.

  1. Install the 2 <G> screws.



6. INSTALL NO. 1 HEATER TO REGISTER DUCT
  1. Install the duct with the 5 <G> screws.



  1. Engage the clamp.


    B192352



7. INSTALL GLOVE BOX LIGHT ASSEMBLY


B192351
  1. Engage the 2 claws to install the glove box light.



8. INSTALL NO. 3 INSTRUMENT PANEL STAY


  1. Engage the 5 claws to install the 5 stays.


    B192329



9. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY (for 8 Speakers)


  1. Engage the 5 claws to install the instrument panel.


    B192375

  1. Install the 3 <C> bolts and 2 <E> nuts.



  1. Install the 2 <F> passenger airbag bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



    B188245E01

  1. Connect the connectors and engage the clamps.



  1. Install the wire harness with the bolt.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }



    B188244



    B192371
  1. Connect the airbag connector.



10. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY (for 14 Speakers)


  1. Engage the 5 claws to install the instrument panel.


    B192375

  1. Install the 3 <C> bolts and 2 <E> nuts.



  1. Install the 2 <F> passenger airbag bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



    B188245E01

  1. Connect the connectors and engage the clamps.



  1. Install the wire harness with the bolt.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }



    B192365



    B192371
  1. Connect the airbag connector.



11. INSTALL NO. 1 INSTRUMENT PANEL SAFETY PAD INSERT


B192337
  1. Connect the connector and engage the clamp.

  1. Engage the 2 claws to install the safety pad insert.

  1. Install the 4 <A> bolts.



12. INSTALL FRONT NO. 4 SPEAKER ASSEMBLY (for 14 Speakers)


B165751E01
  1. Connect the connector.

  1. Temporarily install the speaker by aligning the positioning pins of the speaker with the instrument panel.

  1. Install the speaker with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

    NOTICE:
    1. Do not touch the cone part of the speaker.
    2. When installing the speaker to the instrument panel, be careful that the wires do not get caught between the parts.



13. INSTALL NO. 3 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


B192348
  1. Engage the 6 clips and 2 claws to install the speaker panel.



14. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY RH


E161074
  1. Connect the speaker connector.

  1. Temporarily install the speaker by aligning the positioning pins of the speaker with the instrument panel.

  1. Install the speaker with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

    NOTICE:
    1. Do not touch the cone part of the speaker.
    2. When installing the speaker to the instrument panel, be careful that the wires do not get caught between the parts.



15. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


B192350
  1. Engage the 4 clips and claw install the speaker panel.



16. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY LH


E161075
  1. Connect the speaker connector.

  1. Temporarily install the speaker by aligning the positioning pins of the speaker with the instrument panel.

  1. Install the speaker with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

    NOTICE:
    1. Do not touch the cone part of the speaker.
    2. When installing the speaker to the instrument panel, be careful that the wires do not get caught between the parts.



17. INSTALL INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


B192346
  1. Engage the 4 clips and claw and install the speaker panel.



18. INSTALL NO. 2 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY


    B192344
  1. Engage the clip and install the box door.

  1. Install the 6 <B> screws.



19. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY RH


    B192341
  1. Engage the 4 claws and install the finish panel.

  1. Install the 3 <D> screws and bolt <A>.



20. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


B192340
  1. Engage the 2 guides and 4 claws and install the under cover.



21. INSTALL FRONT PILLAR GARNISH RH


    B190132E01
  1. Remove the protective cover.



  1. Engage the claw to install the front pillar garnish.


    B193062

  1. Install the assist grip with the 2 bolts.

    Torque:
    9.7 N*m{ 99 kgf*cm , 86 in.*lbf }

  1. Engage the 2 claws to install the 2 assist grip plugs.



22. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Install the front door opening trim weatherstrip RH.



23. INSTALL COWL SIDE TRIM BOARD RH


    B190152
  1. Engage the 2 clips to install the cowl side trim board.

  1. Install the clip.



24. INSTALL FRONT DOOR SCUFF PLATE RH


B190151
  1. Engage the 9 claws to install the scuff plate.



25. INSTALL INSTRUMENT SIDE PANEL RH


    B192339
  1. Engage the 3 guides and 3 claws and install the side panel.



26. INSTALL NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System)


E159006
  1. Connect the connectors.

  1. Insert the navigation receiver as shown in the illustration to engage the 3 clips on its backside.

    NOTICE:
    When inserting the navigation receiver, do not press the knobs on it.



    B164792
  1. Install the navigation receiver with the 4 bolts.



27. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Radio Receiver)


E161045
  1. Connect the connectors.

  1. Insert the radio receiver and engage the 3 clips on its backside.

    NOTICE:
    When inserting the radio receiver, do not press its knobs.



    B164786
  1. Install the radio receiver with the 4 bolts.



28. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY


I104352
  1. Connect the connectors.

  1. Engage the 4 clips and install the panel.



29. INSTALL CENTER LOWER INSTRUMENT PANEL FINISH PANEL


    B192336
  1. Connect the connectors.

  1. Engage the 4 clips and 2 claws and install the finish panel.



30. INSTALL COMBINATION METER ASSEMBLY


    E141678
  1. Connect the connector and engage the clip and install the combination meter assembly.



    E161309
  1. Install the 4 screws.



31. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


B192335
  1. Engage the 12 clips and install the finish panel.

  1. Connect the 2 connectors and clamp.



    B192334
  1. Engage the 4 claws and install the instrument panel finish panel retainer.



32. INSTALL FRONT CONSOLE BOX


B188224
  1. Install the front console box with the 5 screws and 2 clips.

  1. Engage the 2 clamps.



33. INSTALL REAR CONSOLE BOX ASSEMBLY


B192330
  1. Engage the 6 claws and install the rear console box.

  1. Install the 2 screws and 4 bolts.



    B188223
  1. Connect the connectors.



34. INSTALL CONSOLE BOX CARPET


B188222
  1. Install the console box carpet.



35. INSTALL REAR UPPER CONSOLE PANEL SUB-ASSEMBLY


    B192328
  1. Connect the connectors.

  1. Engage the 6 clips and install the console panel.

  1. Install the clip.



36. INSTALL REAR CONSOLE BOX POCKET


B188221
  1. Install the rear console box pocket.



37. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY


    B161742
  1. Engage the 12 clips and install the console panel.



38. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


    B167312
  1. Install the shift lever knob and twist it in the direction indicated by the arrow.



39. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH


B192333
  1. Engage the 2 claws and install the sensor.

  1. Connect the connectors.

  1. Engage the 4 clips and claw and install the finish panel.

  1. Install the 2 <A> bolts.



40. INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    B192511
  1. Connect the hood lock control cable assembly to the hood lock control lever sub-assembly.

  1. engage the 3 claws to install the hood lock lever



41. INSTALL INSTRUMENT SIDE PANEL LH


    B192332
  1. Engage the 4 guides and 3 claws and install the side panel.



42. INSTALL FRONT PILLAR GARNISH LH

HINT:
Use the same procedure for both sides.



43. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Install the front door opening trim weatherstrip LH.



44. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure for both sides.



45. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure for both sides.



46. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY


    C159216
  1. Install the turn signal switch with spiral cable to the steering column with the clamp.



    C180951
  1. Connect the 6 connectors to the turn signal switch with spiral cable.



47. INSTALL UPPER STEERING COLUMN COVER


C159215
  1. Attach the claw to install the upper steering column cover.

  1. Attach the 4 clips.



48. INSTALL LOWER STEERING COLUMN COVER


C181134
  1. Attach the 2 claws to install the lower steering column cover.

  1. Install the 2 screws.



49. INSTALL STEERING WHEEL ASSEMBLY


    C181135E01
  1. Align the matchmarks on the steering wheel and steering main shaft.

  1. Install the steering wheel set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



50. INSTALL STEERING PAD

NOTICE:
Do not use a steering pad that has been dropped.



    B166581
  1. Confirm that the ignition switch is turned off.

  1. Confirm that the negative battery terminal is disconnected.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Connect the horn terminal.

  1. Connect the airbag connector.

    NOTICE:
    1. Match the color of the airbag connector with that of the steering pad assembly, and install the airbag connector.
    2. Securely lock the locking button.

  1. Install the steering pad.



    C180935
  1. Using "TORX" socked wrench T30, tighten the 2 screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



51. INSTALL LOWER NO. 3 STEERING WHEEL COVER


    B166432
  1. Attach the 2 claws to install the cover.



52. INSTALL LOWER NO. 2 STEERING WHEEL COVER


    B166433
  1. Attach the 2 claws to install the cover.



53. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

CAUTION:
When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



54. INSPECT SRS WARNING LIGHT
  1. Inspect the SRS warning light (Click here).