Home › Engine / Hybrid System ยท 2UZ-FE › ENGINE CONTROL › HEATED OXYGEN SENSOR

HEATED OXYGEN SENSOR > INSTALLATION

for Preparation Click here



1. INSTALL HEATED OXYGEN SENSOR (for Bank 2 Sensor 2)


A185642E01
  1. Using SST, install the heated oxygen sensor.

    SST
    09224-00010  
    1. without SST

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }

    1. with SST

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.8 in.). If using a torque wrench with a length that is not 30 cm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).
    2. Make sure SST and wrench are connected in a straight line.



    A185640
  1. Connect the heated oxygen sensor connector.



2. INSTALL HEATED OXYGEN SENSOR (for Bank 1 Sensor 2 4WD)


A155874E01
  1. Using SST, install the heated oxygen sensor.

    SST
    09224-00010  
    1. without SST

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }

    1. with SST

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.8 in.). If using a torque wrench with a length that is not 30 cm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).
    2. Make sure SST and wrench are connected in a straight line.



3. INSTALL HEATED OXYGEN SENSOR (for Bank 1 Sensor 2 2WD)


A185639E01
  1. Using SST, install the heated oxygen sensor.

    SST
    09224-00010  
    1. without SST

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }

    1. with SST

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.8 in.). If using a torque wrench with a length that is not 30 cm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).
    2. Make sure SST and wrench are connected in a straight line.



    A185637
  1. Connect the heated oxygen sensor connector.



4. INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY (for 4WD)


    A185632
  1. Install a new gasket and the front No. 2 exhaust pipe assembly to the exhaust manifold LH with 3 new nuts.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

  1. Install a new gasket and the front No. 2 exhaust pipe assembly to the front No. 3 exhaust pipe sub-assembly with the 2 bolts and 2 nuts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

  1. Connect the air fuel ratio sensor connector.

  1. Connect the heated oxygen sensor connector.



5. INSPECT FOR EXHAUST GAS LEAK