Home › Engine / Hybrid System ยท 2UZ-FE › INTAKE / EXHAUST › EXHAUST MANIFOLD

EXHAUST MANIFOLD > REMOVAL

for Preparation Click here



1. REMOVE NO. 1 ENGINE UNDER COVER


    A150108
  1. Remove the 3 screws and 5 bolts.

  1. Unhook the engine under cover from the vehicle body as shown in the illustration.



2. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug and 2 cylinder block drain cock plugs.

  1. Remove the radiator cap. Then drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.



  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 10 ft.*lbf }



    A156211E01

  1. Tighten the radiator drain cock plug by hand.



3. REMOVE THROTTLE BODY COVER SUB-ASSEMBLY


    A153486
  1. Remove the 2 nuts and throttle body cover sub-assembly.



4. REMOVE AIR CLEANER HOSE ASSEMBLY


    A153487
  1. Disconnect the vacuum hose and No. 2 ventilation hose.

  1. Loosen the 2 hose clamps and remove the air cleaner hose assembly.



5. REMOVE AIR CLEANER ASSEMBLY


    A185616
  1. Disconnect the clamp and mass air flow meter connector.

  1. Remove the 2 bolts and remove the air cleaner assembly.



6. REMOVE FRONT FENDER APRON SEAL REAR LH
  1. Remove the 5 clips and fender apron seal.



7. REMOVE FRONT FENDER APRON SEAL LH
  1. Remove the 6 clips and fender apron seal.



8. REMOVE NO. 2 AIR HOSE (for Bank 1)


    A153515
  1. Disconnect the air switching valve assembly connector.

  1. Disconnect the fuel hose clamp.



    A153516
  1. Remove the No. 2 air hose.



9. REMOVE NO. 3 AIR TUBE (for Bank 1)


A153518
  1. Remove the 4 nuts, No. 3 air tube and 2 gaskets.

    NOTICE:
    Be careful not to damage the installation surface of the gaskets.



10. REMOVE AIR SWITCHING VALVE ASSEMBLY (for Bank 1)


A153519E01
  1. Remove the 3 nuts and air switching valve assembly.

    NOTICE:
    Do not hold the bracket of the air switching valve assembly.



11. REMOVE FRONT FENDER APRON SEAL REAR RH
  1. Remove the 5 clips and front fender apron seal rear RH.



12. REMOVE FRONT FENDER APRON SEAL RH
  1. Remove the 6 clips and front fender apron seal RH.



13. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE


    A150112E01
  1. Remove the dipstick.

  1. Remove the bolt and dipstick guide.

  1. Remove the O-ring from the dipstick guide.



14. REMOVE HEATER OUTLET WATER HOSE


A156187


15. DISCONNECT NO. 5 WATER BY-PASS HOSE


    A156193
  1. Loosen the clip and disconnect the No. 5 water by-pass hose.



16. REMOVE WATER BY-PASS PIPE ASSEMBLY


    A156198E01
  1. Disconnect the 2 water hoses from the transmission oil cooler.

  1. Remove the 3 bolts and water by-pass pipe assembly.



17. DISCONNECT NO. 2 AIR INJECTION SYSTEM HOSE (for Bank 2)
  1. Disconnect the No. 2 air injection system hose from the air switching valve assembly.



18. REMOVE NO. 2 AIR TUBE (for Bank 2)


    A153510
  1. Disconnect the air switching valve assembly connector.

  1. Disconnect the wire harness clamp.



    A153512
  1. Remove the 4 nuts, No. 2 air tube and 2 gaskets.

    NOTICE:
    Be careful not to damage the installation surface of the gaskets.



19. REMOVE AIR SWITCHING VALVE ASSEMBLY (for Bank 2)


    A153513E01
  1. Remove the 3 nuts and air switching valve assembly.

    NOTICE:
    Do not hold the bracket of the air switching valve assembly.



20. REMOVE FRONT EXHAUST PIPE ASSEMBLY


    A185633
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the heated oxygen sensor connector and 2 clamps.

  1. Remove the 2 bolts from the center exhaust pipe assembly.

  1. Remove the 3 nuts and front exhaust pipe assembly pipe.



21. REMOVE PROPELLER SHAFT HEAT INSULATOR (for 4WD)


    C158452
  1. Remove the 2 bolts and heat insulator from the heat insulator bracket.



22. REMOVE FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)


    C179230E02
  1. Place matchmarks on the differential and propeller shaft flange.

  1. Place matchmarks on the transfer and propeller shaft flanges.

  1. Remove the 8 nuts and 8 washers and remove the front propeller shaft assembly.



23. REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY


    A185632
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the heated oxygen sensor connector.

  1. Remove the 2 bolts and 2 nuts from the front No. 3 exhaust pipe sub-assembly.

  1. Remove the 3 nuts and front No. 2 exhaust pipe assembly pipe.



24. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    A156201E02
  1. Remove the 4 bolts and No. 1 exhaust manifold heat insulator.



25. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH


    A156203E03
  1. Remove the 8 nuts and exhaust manifold sub-assembly RH.



    A162071E01
  1. Remove the gasket.



26. REMOVE NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY


C155151E01
  1. Put matchmarks on the No. 2 steering intermediate shaft and the power steering gear.

  1. Remove the bolt and No. 2 steering intermediate shaft from the power steering gear.



27. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR


    A156202E02
  1. Remove the 4 bolts and No. 2 exhaust manifold heat insulator.



28. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH


    A156204E02
  1. Remove the 8 nuts and exhaust manifold sub-assembly LH.



    A162072E01
  1. Remove the gasket.