Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM

THEFT DETERRENT SYSTEM > Security Horn Circuit

for Preparation Click here


DESCRIPTION

  1. When the theft deterrent system is operating, the main body ECU outputs a signal continuously at 0.4 second intervals, causing the security horn to sound.

WIRING DIAGRAM


B160795E03


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (SECURITY HORN)
  1. Operate the Techstream according to the steps on the display and select Active Test.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Security Horn
    Security horn
    ON or OFF
    -

    OK:
    Security horn operates normally.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT FUSE (MET-B)


    B191994E01
  1. Remove the MET-B fuse from the engine room relay block unit B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    MET-B fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


3.INSPECT SECURITY HORN RELAY
B060778E04
  1. Remove the security horn relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When battery voltage is not applied between terminals 1 and 2
    10 kΩ or higher
    When battery voltage is applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE SECURITY HORN RELAY
OK


4.INSPECT SECURITY HORN ASSEMBLY


    E140469
  1. Remove the security horn (Click here).

  1. Check operation of the horn.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 1
    Battery negative (-) → Horn bracket
    Horn sounds



NG
REPLACE SECURITY HORN ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (SECURITY HORN RELAY - BATTERY)


    B165963E01
  1. Remove the security horn relay from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Engine room relay block security horn relay terminal 1 - Body ground
    Always
    11 to 14 V
    Engine room relay block security horn relay terminal 3 - Body ground
    Always



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (SECURITY HORN RELAY - SECURITY HORN)


    B165950E02
  1. Remove the security horn relay from the engine room relay block.

  1. Disconnect the A33 security horn connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Engine room relay block security horn relay terminal 5 - A33-1
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SECURITY HORN RELAY)


    B165951E02
  1. Remove the security horn relay from the engine room relay block.

  1. Disconnect the H1 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Engine room relay block security horn relay terminal 2 - H1-6 (SH)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU