Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM

SEAT BELT WARNING SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK COMBINATION METER (METER ECU)

B165617E02

  1. Measure the resistance and voltage according to the value(s) in the table below.

    Standard 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    H37-18 (B) - Body ground
    LG - Body ground
    Power source
    Always
    11 to 14 V
    H37-15 (P/SB) - Body ground
    L - Body ground
    Front passenger side seat belt warning light signal
    Front passenger side seat is occupied, seat belt is fastened
    Below 1 V
    Front passenger side seat is occupied, seat belt is unfastened
    Alternating between 11 to 14 V and below 1 V
    H37-31 (TX+) - Body ground
    Y - Body ground
    Accessory meter input signal
    Ignition switch ON
    Local communication signal
    H37-33 (CANH) - H37-34 (CANL)
    SB - W
    Driver side seat belt warning light signal (CAN signal)
    Ignition switch off
    108 to 132 Ω
    H37-33 (CANH) - H37-40 (E1)
    SB - W-B
    Driver side seat belt warning light signal (CAN signal)
    Ignition switch off
    200 Ω or higher
    H37-34 (CANL) - H37-40 (E1)
    W - W-B
    Driver side seat belt warning light signal (CAN signal)
    Ignition switch off
    200 Ω or higher
    H37-40 (E1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, the ECU may have a malfunction.


CHECK INTEGRATION CONTROL AND PANEL

B165618E02

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    H45-16 (IG+) - Body ground
    P - Body ground
    Power source
    Always
    11 to 14 V
    H45-14 (PBEW) - Body ground
    L - Body ground
    Front passenger side seat belt warning light signal
    Front passenger side seat is occupied, seat belt is fastened
    Below 1 V
    Front passenger side seat is occupied, seat belt is unfastened
    Alternating between 11 to 14 V and below 1 V

    1. If the result is not as specified, the panel may have a malfunction.


CENTER AIRBAG SENSOR

B165619E06


Terminal No.
Terminal Symbol
Destination
H56-13
CANH
Combination meter
(Meter ECU)
H56-22
CANL
Combination meter
(Meter ECU)
O1-11
DBE+
Front seat inner belt LH (Seat belt buckle switch LH)
O1-12
DBE-
Front seat inner belt LH (Seat belt buckle switch LH)
P1-12
FSP+
Occupant classification ECU
P1-13
FSP-
Occupant classification ECU

CHECK OCCUPANT CLASSIFICATION ECU

B165620E02

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard: (w/ Power Seat) 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    W6-1 (+B) - Body ground
    G - Body ground
    Power source
    Always
    11 to 14 V
    W6-7 (IG) - Body ground
    SB - Body ground
    Occupant classification ECU +B line
    Ignition switch ON
    11 to 14 V
    W6-4 (FSR-) - W6-8 (FSR+)
    B - W
    Pressure sensor signal line
    Ignition switch ON
    Below 1 to 5 V
    W6-9 (BSW) - W6-5 (BGND)
    L - BE
    Passenger side buckle switch line
    Ignition switch ON
    Pulse generation
    W6-3 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    Standard: (w/o Power Seat) 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    P14-1 (+B) - Body ground
    R - Body ground
    Power source
    Always
    11 to 14 V
    P14-7 (IG) - Body ground
    SB - Body ground
    Occupant classification ECU +B line
    Ignition switch ON
    11 to 14 V
    P14-4 (FSR-) - P14-8 (FSR+)
    B - W
    Pressure sensor signal line
    Ignition switch ON
    Below 1 to 5 V
    P14-9 (BSW) - P14-5 (BGND)
    L - BE
    Passenger side buckle switch line
    Ignition switch ON
    Pulse generation
    P14-3 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, the ECU may have a malfunction.