FRONT DOOR > DISASSEMBLY |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH (for 14 Speakers) |
![]() |
Disengage the 3 clips and remove the front door lower frame bracket garnish.
Disconnect the connector.
| 3. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH |
![]() |
Disengage the 3 clips and remove the front door lower frame bracket garnish.
| 4. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Using a moulding remover, disengage the 4 claws and remove the front door inside handle bezel plug.
| 5. REMOVE FRONT ARMREST BASE UPPER PANEL |
![]() |
Disengage the 2 clips and 5 claws and remove the front armrest base upper panel.
Disconnect the connector.
| 6. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Remove the front door armrest cover.
Remove the 2 screws.
![]() |
Disengage the 10 clips.
Disconnect the connector.
![]() |
Disconnect the front door lock remote control cable and front door inside locking cable and remove the front door trim board sub-assembly.
| 7. REMOVE SEAT MEMORY SWITCH (for Driver Side with Memory) |
![]() |
Remove the 2 screws and seat memory switch.
| 8. REMOVE FRONT DOOR INSIDE HANDLE BEZEL |
![]() |
Remove the 4 screws and remove the front door inside handle bezel.
| 9. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY |
![]() |
Remove the 3 screws and remove the front door inside handle sub-assembly.
| 10. REMOVE FRONT DOOR GLASS INNER WEATHERSTRIP |
![]() |
Raise the 8 claws of the front door glass inner weatherstrip and then remove the front door glass inner weatherstrip from the front door trim board sub-assembly, as shown in the illustration.
| 11. REMOVE SIDE AIR BAG SENSOR ASSEMBLY |
![]() |
Slide the outer housing and disconnect the airbag connector.
Remove the bolt.
Disengage the guide and remove the side airbag sensor.
| 12. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY |
![]() |
Disconnect the speaker connector.
Remove the 4 screws.
![]() |
Disengage the 3 claws and remove the speaker.
| 13. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY |
![]() |
Disconnect the connector.
Remove the 3 nuts.
Disengage the claw and remove the outer rear view mirror assembly.
| 14. REMOVE FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY |
![]() |
Apply protective tape to the door panel in the area around the front door glass outer weatherstrip.
![]() |
Using a moulding remover, disengage the 5 claws and the clip and remove the front door glass outer weatherstrip.
| 15. REMOVE OUTER MIRROR CONTROL ECU ASSEMBLY (for Driver Side with Memory) |
![]() |
Disconnect the 2 connectors.
Remove the 2 screws and remove the outer mirror control ECU assembly.
| 16. REMOVE FRONT DOOR NO. 1 TRIM BRACKET |
![]() |
Remove the 2 screws and remove the front door No. 1 trim bracket.
| 17. REMOVE FRONT DOOR SERVICE HOLE COVER |
![]() |
Disconnect the connectors and disengage the clamps.
![]() |
Remove the front door service hole cover.
| 18. REMOVE FRONT DOOR GLASS RUN |
![]() |
Remove the front door glass run.
| 19. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY |
![]() |
Provisionally install the power window switch.
Move the front door glass until the 2 bolts can be seen through the service holes.
Remove the 2 bolts.
![]() |
Remove the front door glass sub-assembly in the direction indicated by the arrows in the illustration.
Remove the power window switch.
| 20. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY |
![]() |
Disconnect the connector.
Loosen bolt A.
Remove the 5 bolts, then remove the front door window regulator sub-assembly.
| 21. REMOVE FRONT DOOR FRAME FRONT LOWER SUB-ASSEMBLY |
![]() |
Remove the 2 bolts and remove the front door frame front lower sub-assembly.
| 22. REMOVE FRONT DOOR FRAME REAR LOWER SUB-ASSEMBLY |
![]() |
Remove the 2 bolts and remove the front door frame rear lower sub-assembly.
| 23. REMOVE FRONT NO. 1 DOOR STIFFENER CUSHION |
![]() |
Disengage the 2 clips and remove the front No. 1 door stiffener cushion.
| 24. REMOVE FRONT DOOR CHECK ASSEMBLY |
![]() |
Remove the 2 nuts and bolt and remove the front door check assembly.
| 25. REMOVE FRONT DOOR WEATHERSTRIP |
![]() |
Disengage the 39 clips and remove the front door weatherstrip.
| 26. REMOVE FRONT DOOR PANEL PROTECTOR |
![]() |
Disengage the 8 clips and remove the front door panel protector.
| 27. REMOVE FRONT DOOR OUTSIDE HANDLE COVER |
![]() |
Remove the hole plug.
Using "TORX" socket wrench T30, loosen the screw and remove the front door outside handle cover.
| 28. REMOVE DOOR LOCK CYLINDER (for Driver Side) |
![]() |
Disengage the 2 claws and remove the door lock cylinder.
| 29. REMOVE FRONT DOOR LOCK |
![]() |
Using a "TORX" socket wrench T30, remove the 3 screws.
Slide the front door lock downward, pull out the front door lock open rod from the outside handle frame, and remove the front door lock and cables as a unit.
Remove the door lock wire harness seal from the front door lock.
![]() |
Remove the front door lock remote control cable.
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and open the cover.
![]() |
Remove the front door inside locking cable.
| 30. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY |
![]() |
Remove the front door handle assembly by sliding and pulling it in the direction indicated by the arrow mark in the illustration.
| 31. REMOVE FRONT DOOR OUTSIDE HANDLE REAR PAD |
![]() |
Disengage the 2 claws and remove the front door outside handle rear pad.
| 32. REMOVE FRONT DOOR OUTSIDE HANDLE FRONT PAD |
![]() |
Disengage the 3 claws and remove the front door outside handle front pad.
| 33. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY |
![]() |
Using "TORX" socket wrench T30, loosen the screw.
Disengage the claw and slide the front door outside handle frame sub-assembly to remove it.
| 34. REMOVE CUSHION |
![]() |
Remove the cushions from the door panel.