Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR

REAR DOOR > REASSEMBLY

for Preparation Click here



1. INSTALL CUSHION


    B192118
  1. Install the cushions onto the door panel.



2. INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


    B195034
  1. Slide the rear door outside handle frame subassembly and engage the claw and install it.

  1. Using a T30 "TORX" wrench, tighten the screw

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



3. INSTALL REAR DOOR OUTSIDE HANDLE FRONT PAD


    B192116
  1. Engage the 2 claws and install the rear door outside handle front pad.



4. INSTALL REAR DOOR OUTSIDE HANDLE REAR PAD


    B192115
  1. Engage the 2 claws and install the rear door outside handle rear pad.



5. INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY


    B192113
  1. Install the rear door outside handle assembly by pushing it in the direction indicated by the arrow mark shown in the illustration.



6. INSTALL REAR DOOR OUTSIDE HANDLE COVER


    B192111
  1. Using "TORX" socket wrench T30, install the rear door outside handle cover with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



7. INSTALL REAR DOOR LOCK
  1. Apply MP grease to the sliding and rotating areas of the front door lock.



    B192550
  1. Install the rear door inside locking cable.



    B192549
  1. Engage the 3 claws and close the cover.



    B192547
  1. Install the rear door lock remote control cable.



    B192546
  1. Engage the claw and close the cover.

  1. Install a new door lock wire harness seal on to the rear door lock.



    B192117
  1. Insert the rear door lock into the rear door outside handle release plate, and set it to the rear door panel.

  1. Make sure that the rear door outside handle frame lock.

  1. Apply adhesive to the threads of the screws.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Using a "TORX" socket wrench T30, install the rear door lock with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



8. INSTALL REAR DOOR NO. 2 WEATHERSTRIP


B192110
  1. Engage the 17 clips and install the rear door No. 2 weatherstrip.



9. INSTALL REAR DOOR WEATHERSTRIP


B192109
  1. Engage the 42 clips and install the rear door weatherstrip.



10. INSTALL REAR DOOR CHECK ASSEMBLY


B190589
  1. Apply MP grease to the sliding areas of the rear door check assembly.

  1. Install the rear door check assembly onto the door panel with the 2 nuts.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

  1. Apply adhesive to the threads of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or Equivalent

  1. Install the rear door check assembly onto the body panel with the bolt.

    Torque:
    29 N*m{ 296 kgf*cm , 21 in.*lbf }



11. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY


    B192108E01
  1. Apply MP grease to the sliding and rotating areas of the rear door window regulator sub-assembly.

    NOTICE:
    Do not apply grease to the front door window regulator spring.

  1. Loosely screw bolt A onto the rear door window regulator sub-assembly.

  1. Insert the rear door window regulator sub-assembly into the door panel. Provisionally tighten bolt A to hang the rear door window regulator sub-assembly on the door panel.

    NOTICE:
    Do not drop the front door window regulator sub-assembly as it may be damaged.

  1. Install the front door window regulator sub-assembly with the 5 bolts, and tighten bolt A.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.



12. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    B190588
  1. Install the rear door glass sub-assembly onto the rear door window regulator with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



13. INSTALL REAR DOOR WINDOW GUIDE FRONT SUB-ASSEMBLY


    B190587
  1. Install the rear door window guide front sub-assembly with the 2 bolts

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



14. INSTALL REAR DOOR WINDOW FRAME REAR LOWER SUB-ASSEMBLY


B190586
  1. Install the rear door window frame rear lower sub-assembly with the nut and 3 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



15. INSTALL SUNSHADE HOOK


    B194496
  1. Engage the claw and install the sunshade hook.



16. INSTALL REAR DOOR GLASS RUN


    B190585
  1. Install the rear door glass run.



17. INSTALL REAR DOOR GLASS OUTER WEATHERSTRIP


B191705
  1. Engage the 5 claws and clip and install a new rear door glass outer weatherstrip.



18. INSTALL REAR DOOR WINDOW FRAME REAR MOULDING
  1. Apply Primer G to the installation part of rear door window frame rear moulding.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

  1. Remove the release paper from the rear door window frame rear moulding.



    B191717
  1. Engage the claw and clip and install the rear door window frame rear moulding.



19. INSTALL REAR DOOR SERVICE HOLE COVER


    B195022
  1. Apply butyl tape to the door panel, then install a new rear door service hole cover as shown in the illustration.

    HINT:
    1. When installing the service hole cover, pull the links and connectors out through the service hole.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the quality of the seal.



    B190584
  1. Engage the clamps and connect the connectors.



20. INSTALL REAR DOOR TRIM NO. 2 BRACKET


    B190583
  1. Install the rear door trim No. 2 bracket with the 2 screws.



21. INSTALL REAR NO. 1 SPEAKER ASSEMBLY


    E161077
  1. Engage the 2 claws.



    E161073
  1. Install the speaker with the 3 screws.

    NOTICE:
    Do not touch the cone part of the speaker.

  1. Connect the connector.



22. INSTALL REAR DOOR GLASS INNER WEATHERSTRIP


    B190582
  1. Install the rear door glass inner weatherstrip on the rear door trim board sub-assembly and fold down the 8 claws, as shown in the illustration.



23. INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


    B190545
  1. Install the rear door inside handle sub-assembly with the 3 screws.



24. INSTALL REAR DOOR INSIDE HANDLE BEZEL


    B190544
  1. Install the rear door inside handle bezel with the 4 screws.



25. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    B190580
  1. Connect the rear door lock remote control cable and the rear door inside locking cable.

  1. Connect the connector.



    B190579
  1. Engage the 9 clips and install the rear door trim board sub-assembly.



    B190578
  1. Tighten the 2 screws.

  1. Install the rear door armrest cover.



26. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG


B190576
  1. Engage the 4 claws and install the rear door inside handle bezel plug.



27. INSTALL REAR DOOR ARMREST BASE UPPER PANEL
  1. Connect the connector.



    B190574
  1. Engage the 2 clips and 5 claws and install the rear door armrest base upper panel.



28. INSTALL REAR DOOR FRAME GARNISH


    B190577
  1. Engage the 6 clips and install the rear door frame garnish.



29. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

CAUTION:
When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).



30. INSPECT SRS WARNING LIGHT
  1. Inspect the SRS warning light (Click here).