Home › Drivetrain ยท JF3A TRANSFER / 4WD / AWD › TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM

TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM > SYSTEM DESCRIPTION

for Preparation Click here



DESCRIPTION
  1. Through the combination of the JF3A transfer system and A.D.D. (Automatic Disconnecting Differential), the multi-mode 4WD system maximizes dynamic performance and achieves efficient running by enabling an optimal driving mode to be selected from the 5 types of driving range (H2, H4F, H4L, L4F and L4L) in accordance with the road conditions. Driving mode is selected by operating the 4WD control switch and the center differential lock switch.
  2. Through these switch signals, the 4WD control ECU actuates the 2 shift motors in the transfer shift actuator and another shift motor in the A.D.D. shift actuator.

DRIVING MODE SWITCHING PATTERN
As indicated by the 4WD mode switching pattern illustrated below, the 4WD control switch and the center differential lock switch do not operate simultaneously while switching H-L.

C179933E01

  1. This signal becomes inactive even if the center differential lock switch is turned ON during H-L switching.
  2. When the driver switches H-L while the center differential lock is switching, the actual H-L switching takes place after the center differential has been locked.


  1. 4WD Mode Switching Pattern


    C179932E01

    H2: High Speed 2WD
    H4F: High Speed 4WD and Center Differential Free
    H4L: High Speed 4WD and Center Differential Lock
    L4F: Low Speed 4WD and Center Differential Free
    L4L: Low Speed 4WD and Center Differential Lock

    HINT:
    1. *1: If the center differential switch is turned ON while switching from H2 to H4F, it will proceed directly to the H4L mode without engaging the H4F mode.
    2. *2: H2 → H4F switching cannot be made unless the vehicle speed is less than 100 km/h (62 mph). If H2 → H4F switching is operated in any other condition, the 4HI indicator light blinks and the buzzer sounds in the combination meter. (To cancel: 4WD control switch is returned to its original position.)
    3. *3: H-L switching cannot be made unless the A/T shift position is N.
      If the 4WD control switch is operated in any other condition, the 4LO indicator light blinks and the buzzer sounds in the combination meter. (To cancel: 4WD control switch is returned to its original position.)


FUNCTION OF COMPONENTS

Components
Functions
4HI indicator light
Indicates that the transfer mode is 4WD HIGH (H4).
4LO indicator light
Indicates that the transfer mode is 4WD LOW (L4).
CENTER DIFF. indicator light
Indicates that the center differential is in LOCK mode
Warning buzzer
Sounds an alarm if a violation of the conditions required for mode shifting occurs when the transfer mode is shifted.
Center differential lock switch
Selects the center differential mode between LOCK and FREE.
4WD control switch
Controls the transfer assembly and A.D.D. actuator to select transfer mode among H2, H4, and L4.
Multi mode limit switch
Detects when the transfer mode is H2, 4L or 4F.
High-low limit switch
Detects when the transfer mode is H4 or L4.
Center differential lock position detection switch
Detects when the center differential is in LOCK mode (transfer mode either H4L or L4L).
Actuator temperature sensor
Detects the temperature inside the transfer shift actuator.
Transfer shift actuator
Shifts the transfer mode between 2WD and 4WD, the center differential between LOCK and FREE, and the gear reduction mechanism between HIGH and LOW.
A.D.D. actuator
Shifts the front differential between FREE and LOCK.
A.D.D. detection switch
Detects when the front differential is in LOCK mode.
4WD control computer
Controls the shift actuator, A.D.D. motor, and indicator lamp based on signals from each switch.