Home › Engine / Hybrid System ยท 3UR-FE › INTAKE / EXHAUST › EXHAUST MANIFOLD

EXHAUST MANIFOLD > INSTALLATION

for Preparation Click here



1. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH


    A162117E01
  1. Install a new gasket to the cylinder head and a new gasket to the No. 2 air tube.

    HINT:
    1. Install the exhaust manifold gasket with the gasket tab facing toward the front of the engine.
    2. Install the air tube gasket with the gasket's claws facing the tube side.



    A162754E01
  1. Temporarily install the exhaust manifold with the 2 nuts labeled A and 8 new nuts.

  1. Uniformly tighten the nuts that are not labeled A, and then tighten the 2 nuts labeled A.

    1. for nut A

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    1. except nut A

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }



2. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    A162752
  1. Install the No. 1 exhaust manifold heat insulator with the 3 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



3. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH


    A162119E01
  1. Install a new gasket to the cylinder head and a new gasket to the No. 3 air tube.

    HINT:
    1. Install the exhaust manifold gasket with the gasket tab facing toward the rear of the engine.
    2. Install the air tube gasket with the gasket's claws facing the tube side.



    A162115E01
  1. Temporarily install the exhaust manifold with the 2 nuts labeled A and 8 new nuts.

  1. Uniformly tighten the nuts that are not labeled A, and then tighten the 2 nuts labeled A.

    1. for nut A

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    1. except nut A

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }



4. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR


    A162114
  1. Install the No. 2 exhaust manifold heat insulator with the 3 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



5. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY


    A168654E01
  1. Align the matchmarks and insert the No. 2 steering intermediate shaft sub-assembly into the intermediate shaft.



    A168655E01
  1. Align the matchmarks and insert the No. 2 steering intermediate shaft sub-assembly into the power steering gear.

  1. Install the 2 bolts.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



6. INSTALL FRONT NO. 4 FLOOR HEAT INSULATOR


A184951
  1. Install the front No. 4 floor heat insulator with the 4 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



7. INSTALL FRONT NO. 3 FLOOR HEAT INSULATOR


A184950
  1. Install the front No. 3 floor heat insulator with the 4 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



8. INSTALL FRONT EXHAUST PIPE ASSEMBLY


A184982
  1. Install a new gasket and the front exhaust pipe assembly to the exhaust manifold RH with 3 new nuts.

    Torque:
    54 N*m{ 554 kgf*cm , 40 ft.*lbf }

  1. Install a new gasket and the front exhaust pipe assembly to the center exhaust pipe assembly with the 2 bolts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

  1. Connect the air fuel ratio sensor connector.

  1. Connect the heated oxygen sensor connector and 2 clamps.



9. INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY


A184304
  1. Install a new gasket and the front No. 2 exhaust pipe sub-assembly to the exhaust manifold LH with 3 new nuts.

    Torque:
    54 N*m{ 554 kgf*cm , 40 ft.*lbf }



    A184981
  1. Connect the front No. 3 exhaust pipe sub-assembly to the exhaust pipe support.

  1. Install 2 new gaskets and the front No. 3 exhaust pipe sub-assembly with the 4 bolts and 2 new nuts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

  1. Connect the air fuel ratio sensor connector.

  1. Connect the heated oxygen sensor connector.



10. INSTALL FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)


    C179230E02
  1. Align the matchmarks on the differential and propeller shaft flange.

  1. Align the matchmarks on the transfer and propeller shaft flange.

  1. Install the front propeller shaft assembly with the 8 nuts and 8 washers.

    Torque:
    80 N*m{ 816 kgf*cm , 59 ft.*lbf }



11. INSTALL PROPELLER SHAFT HEAT INSULATOR (for 4WD)


C158452
  1. Install the heat insulator to the heat insulator bracket with the 2 bolts.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }



12. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
  1. Apply a light coat of engine oil to a new O-ring.



    A164434E02
  1. Install the O-ring to the guide.

  1. Install the dipstick guide with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the wire harness clamp.

  1. Install the dipstick.



13. INSPECT FOR EXHAUST GAS LEAK
If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.


14. INSTALL FRONT FENDER APRON SEAL REAR LH
  1. Install the fender apron seal with the 5 clips.



15. INSTALL FRONT FENDER APRON SEAL LH
  1. Install the fender apron seal with the 6 clips.



16. INSTALL FRONT FENDER APRON SEAL REAR RH
  1. Install the fender apron seal with the 5 clips.



17. INSTALL FRONT FENDER APRON SEAL RH
  1. Install the fender apron seal with the 6 clips.



18. INSTALL NO. 1 ENGINE UNDER COVER


    A150108
  1. Hook the engine under cover to the vehicle body as shown in the illustration.

  1. Install the 3 screws and 5 bolts.

    1. Bolt

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

    1. Screw

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }