EXHAUST MANIFOLD > INSTALLATION |
| 1. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH |
![]() |
Install a new gasket to the cylinder head and a new gasket to the No. 2 air tube.
![]() |
Temporarily install the exhaust manifold with the 2 nuts labeled A and 8 new nuts.
Uniformly tighten the nuts that are not labeled A, and then tighten the 2 nuts labeled A.
| 2. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR |
![]() |
Install the No. 1 exhaust manifold heat insulator with the 3 bolts.
| 3. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH |
![]() |
Install a new gasket to the cylinder head and a new gasket to the No. 3 air tube.
![]() |
Temporarily install the exhaust manifold with the 2 nuts labeled A and 8 new nuts.
Uniformly tighten the nuts that are not labeled A, and then tighten the 2 nuts labeled A.
| 4. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR |
![]() |
Install the No. 2 exhaust manifold heat insulator with the 3 bolts.
| 5. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY |
![]() |
Align the matchmarks and insert the No. 2 steering intermediate shaft sub-assembly into the intermediate shaft.
![]() |
Align the matchmarks and insert the No. 2 steering intermediate shaft sub-assembly into the power steering gear.
Install the 2 bolts.
| 6. INSTALL FRONT NO. 4 FLOOR HEAT INSULATOR |
![]() |
Install the front No. 4 floor heat insulator with the 4 bolts.
| 7. INSTALL FRONT NO. 3 FLOOR HEAT INSULATOR |
![]() |
Install the front No. 3 floor heat insulator with the 4 bolts.
| 8. INSTALL FRONT EXHAUST PIPE ASSEMBLY |
![]() |
Install a new gasket and the front exhaust pipe assembly to the exhaust manifold RH with 3 new nuts.
Install a new gasket and the front exhaust pipe assembly to the center exhaust pipe assembly with the 2 bolts.
Connect the air fuel ratio sensor connector.
Connect the heated oxygen sensor connector and 2 clamps.
| 9. INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY |
![]() |
Install a new gasket and the front No. 2 exhaust pipe sub-assembly to the exhaust manifold LH with 3 new nuts.
![]() |
Connect the front No. 3 exhaust pipe sub-assembly to the exhaust pipe support.
Install 2 new gaskets and the front No. 3 exhaust pipe sub-assembly with the 4 bolts and 2 new nuts.
Connect the air fuel ratio sensor connector.
Connect the heated oxygen sensor connector.
| 10. INSTALL FRONT PROPELLER SHAFT ASSEMBLY |
![]() |
Align the matchmarks on the differential and propeller shaft flange.
Align the matchmarks on the transfer and propeller shaft flange.
Install the front propeller shaft assembly with the 8 nuts and 8 washers.
| 11. INSTALL PROPELLER SHAFT HEAT INSULATOR |
![]() |
Install the heat insulator to the heat insulator bracket with the 2 bolts.
| 12. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE |
Apply a light coat of engine oil to a new O-ring.
![]() |
Install the O-ring to the guide.
Install the dipstick guide with the bolt.
Connect the wire harness clamp.
Install the dipstick.
| 13. INSPECT FOR EXHAUST GAS LEAK |
| 14. INSTALL FRONT FENDER APRON SEAL REAR LH |
Install the fender apron seal with the 5 clips.
| 15. INSTALL FRONT FENDER APRON SEAL LH |
Install the fender apron seal with the 6 clips.
| 16. INSTALL FRONT FENDER APRON SEAL REAR RH |
Install the fender apron seal with the 5 clips.
| 17. INSTALL FRONT FENDER APRON SEAL RH |
Install the fender apron seal with the 6 clips.
| 18. INSTALL NO. 1 ENGINE UNDER COVER |
![]() |
Hook the engine under cover to the vehicle body as shown in the illustration.
Install the 3 screws and 5 bolts.