EXHAUST MANIFOLD > REMOVAL |
| 1. REMOVE NO. 1 ENGINE UNDER COVER |
![]() |
Remove the 3 screws and 5 bolts.
Unhook the engine under cover from the vehicle body as shown in the illustration.
| 2. REMOVE FRONT FENDER APRON SEAL RH |
Remove the 6 clips and fender apron seal.
| 3. REMOVE FRONT FENDER APRON SEAL REAR RH |
Remove the 5 clips and fender apron seal.
| 4. REMOVE FRONT FENDER APRON SEAL LH |
Remove the 6 clips and fender apron seal.
| 5. REMOVE FRONT FENDER APRON SEAL REAR LH |
Remove the 5 clips and fender apron seal.
| 6. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE |
Remove the dipstick.
Disconnect the wire harness clamp.
![]() |
Remove the bolt and dipstick guide.
Remove the O-ring from the dipstick guide.
| 7. REMOVE PROPELLER SHAFT HEAT INSULATOR |
![]() |
Remove the 2 bolts and heat insulator from the heat insulator bracket.
| 8. REMOVE FRONT PROPELLER SHAFT ASSEMBLY |
![]() |
Place matchmarks on the differential and propeller shaft flange.
Place matchmarks on the transfer and propeller shaft flanges.
Remove the 8 nuts and 8 washers and remove the front propeller shaft assembly.
| 9. REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY |
![]() |
Remove the 2 bolts from the center exhaust pipe.
Remove the 2 bolts and 2 nuts from the front No. 2 exhaust pipe sub-assembly.
Disconnect the front No. 3 exhaust pipe sub-assembly and from exhaust pipe support.
Remove the 2 gaskets.
Disconnect the air fuel ratio sensor connector.
Disconnect the heated oxygen sensor connector.
![]() |
Remove the 3 nuts, No. 2 exhaust pipe sub-assembly and gasket.
| 10. REMOVE FRONT EXHAUST PIPE ASSEMBLY |
Disconnect the air fuel ratio sensor connector.
Disconnect the heated oxygen sensor connector and 2 clamps.
![]() |
Remove the 2 bolts from the center exhaust pipe.
Remove the 3 nuts, front exhaust pipe and 2 gaskets.
| 11. REMOVE FRONT NO. 4 FLOOR HEAT INSULATOR |
![]() |
Remove the 4 nuts and front No. 4 floor heat insulator.
| 12. REMOVE FRONT NO. 3 FLOOR HEAT INSULATOR |
![]() |
Remove the 4 nuts and front No. 3 floor heat insulator.
| 13. REMOVE NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY |
![]() |
Put matchmarks on the No. 2 steering intermediate shaft sub-assembly and steering intermediate shaft.
Remove the bolt and disconnect the No. 2 steering intermediate shaft sub-assembly from the steering intermediate shaft.
![]() |
Put matchmarks on the No. 2 steering intermediate shaft sub-assembly and the power steering gear.
Remove the bolt and disconnect the No. 2 steering intermediate shaft sub-assembly from the power steering gear.
| 14. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR |
![]() |
Remove the 3 bolts and No. 2 exhaust manifold heat insulator.
| 15. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH |
![]() |
Remove the 10 nuts, exhaust manifold sub-assembly LH and 2 gaskets.
| 16. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR |
![]() |
Remove the 3 bolts and No. 1 exhaust manifold heat insulator.
| 17. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH |
![]() |
Remove the 10 nuts, exhaust manifold sub-assembly RH and 2 gaskets.