Home › Vehicle Interior › SEAT › REAR NO. 1 SEAT ASSEMBLY

REAR NO. 1 SEAT ASSEMBLY > DISASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The procedure listed below is for the RH side.



1. REMOVE RECLINING ADJUSTER KNOB CAP RH


    B191081E01
  1. Using a screwdriver, disengage the 3 claws and remove the reclining adjuster knob cap.

    HINT:
    Tape the screwdriver tip before use.



2. REMOVE REAR SEAT RECLINING RELEASE LEVER


    B191083
  1. Remove the 3 screws and rear seat reclining release lever.



3. REMOVE REAR SEAT CUSHION HINGE COVER NO. 3


B191084
  1. Remove the screw.

  1. Disengage the 2 claws and remove the rear seat cushion hinge cover.



4. REMOVE REAR SEAT CUSHION HINGE COVER NO. 2


B191085
  1. Remove the screw.

  1. Disengage the 2 claws and remove the rear seat cushion hinge cover.



5. REMOVE REAR SEAT INNER BELT ASSEMBLY


    B191087
  1. Remove the bolt and remove the rear seat inner belt assembly.



6. REMOVE REAR NO. 1 SEAT CUSHION ASSEMBLY RH


    B191090
  1. Disconnect the connector and disengage the 3 clamps.

    HINT:
    If the vehicle is equipped with the seat heater system, disconnect the connector and disengage the clamps.



    B191088
  1. Cut the cable tie.

  1. Disconnect the cable from the seat cushion spring.



    B191089
  1. Cut the cable tie to remove the cable from the seat cushion spring.

  1. Disengage the cable clamp and remove the cable from the seat cushion spring.



    B200239
  1. Cut the 2 cable ties to remove the cable from the seat cushion spring.



    B191091
  1. Remove the 2 bolts.

  1. Using a T45 "TORX" socket, remove the 2 bolts and 2 bushes. Then remove the rear No. 1 seat cushion assembly.



7. REMOVE REAR SEAT CUSHION SPRING ASSEMBLY RH (w/ Seat Heater System)


    B200241
  1. Remove the 9 hog rings.



    B200247
  1. Disengage the hooks and remove the rear seat cushion spring assembly.



8. REMOVE REAR SEAT CUSHION SPRING ASSEMBLY RH (w/o Seat Heater System)


    B200241
  1. Remove the 9 hog rings.



    B191092
  1. Disengage the hooks and remove the rear seat cushion spring assembly.



9. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER


    B191094
  1. Remove the 11 hog rings and separate type rear seat cushion cover.



10. REMOVE SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)


    B191109
  1. Cut off the tack pins which fasten the seat heater to the seat cushion cover, and then remove the seat cushion heater from the seat cushion cover.



11. REMOVE NO. 1 SEAT CUSHION COVER RH


    B191122
  1. Disengage the cable clamp and disconnect the cable from the No. 1 seat cushion cover.

  1. Remove the 2 screws.

  1. Disengage the claw and remove the No. 1 seat cushion cover.



12. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY RH (w/ Seat Heater System)


    B200248
  1. Cut the cable tie.

  1. Disengage the 5 harness clamps and remove the seat heater control sub-assembly.

  1. Disconnect the seat heater connector.



13. REMOVE REAR SEAT HEADREST ASSEMBLY


14. REMOVE REAR SEATBACK LOCK STRIKER COVER


    B191098E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and guide and remove the rear seatback lock striker cover.



15. REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH


    B191100
  1. Remove the 2 screws.

  1. Disconnect the cable and remove the rear seat lock control lever sub-assembly.



16. REMOVE REAR NO. 1 SEAT ARMREST CAP (w/ Armrest)


    B195221
  1. Disengage the 3 claws and remove the rear No. 1 seat armrest cap.



17. REMOVE SEAT ARMREST ASSEMBLY RH (w/ Armrest)


    B195222
  1. Remove the bolt and seat armrest assembly.



18. REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY RH


    B191101
  1. Disengage the 7 clips and remove the rear seatback board sub-assembly.



19. REMOVE REAR SEAT CUSHION HINGE COVER NO. 1


    B191095
  1. Remove the screw.

  1. Disengage the 4 claws and clip and remove the rear seat cushion hinge cover.



20. REMOVE REAR SEAT CUSHION HINGE COVER RH


    B191096
  1. Remove the 2 screws.

  1. Disengage the 3 claws and remove the rear seat cushion hinge cover.



21. REMOVE REAR SEAT CUSHION UNDER COVER RH


    B191097
  1. Remove the 3 screws and rear seat cushion under cover.



22. REMOVE REAR SEAT HEADREST SUPPORT


    B191133
  1. Disengage the 4 claws and remove the 2 rear seat headrest supports.



23. REMOVE NO. 1 SEATBACK COVER SUB-ASSEMBLY RH


    B200243
  1. Remove the 2 hog rings.

  1. Remove the hooks and No. 1 seatback cover sub-assembly.



24. REMOVE SEATBACK COVER WITH PAD


    B191102
  1. Remove the 2 hog rings.



    B191104
  1. Disengage the hooks and remove the seatback cover with pad.



25. REMOVE SEPARATE TYPE REAR SEATBACK COVER


    B191106
  1. Remove the 8 hog rings and separate type rear seatback cover from the seatback pad.



26. REMOVE SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)


    B191093
  1. Cut off the tack pins which fasten the seat heater to the seatback cover ,and then remove the seatback heater from the seatback cover.



27. REMOVE REAR SEAT RECLINING COVER NO. 1 LH


    B191110
  1. Remove the screw.

  1. Disengage the guide and remove the rear seat reclining cover.



28. REMOVE REAR SEAT RECLINING COVER INNER RH


    B191118
  1. Pull the cable through the rear seatback frame sub-assembly.



    B191112
  1. Remove the screw.

  1. Disengage the 3 claws and remove the rear seat reclining cover.



29. REMOVE REAR SEATBACK FRAME SUB-ASSEMBLY RH


    B191113
  1. Disconnect the 2 clamps.

  1. Rotate the cable ends and remove the cables.



    B191115
  1. Cut the cable tie.

  1. Disconnect the 2 cables from the rear seatback frame sub-assembly.

    HINT:
    When removing the upper cable, operate the release pedal at the back of the seat to make it easier to disconnect the cable. However, be careful because the seatback will fall forward.



    B191117
  1. Using a T40 "TORX" socket, remove the 5 bolts and rear seatback frame sub-assembly.



30. REMOVE REAR SEAT CUSHION HOLDER BRACKET RH


    B200245
  1. Remove the bolt and rear seat cushion holder bracket.



31. REMOVE REAR BACK LOCK CONTROL LEVER SUB-ASSEMBLY RH


    B200246
  1. Remove the E ring and washer.



    B191119
  1. Using a T40 "TORX" socket, remove the bolt.

  1. Remove the 3 nuts to remove the rear back lock control lever sub-assembly and rear seat cushion lock striker sub-assembly.



32. REMOVE REAR SEAT RECLINING COVER INNER LH


    B191111
  1. Remove the screw.

  1. Disengage the guide and remove the rear seat reclining cover.



33. REMOVE REAR SEAT RECLINING COVER INNER


    B191121
  1. Remove the 2 screws and rear seat reclining cover.



34. REMOVE REAR SEATBACK COVER LH


    B195212
  1. Remove the screw and rear seatback cover.

  1. Disengage the cable clamp and disconnect the rear seatback lock control No. 2 cable sub-assembly.



35. REMOVE REAR SEATBACK COVER RH


    B195213
  1. Remove the screw and rear seatback cover.



36. REMOVE REAR SEATBACK LOCK CONTROL NO. 2 CABLE SUB-ASSEMBLY


    B195214
  1. Disconnect the rear seatback lock control No. 2 cable sub-assembly.

    HINT:
    1. The front nut is locked with adhesive. Loosen the rear nut to remove the cable.
    2. If the front nut becomes loose, adjust the length when installing the cable.

  1. Rotate the cable end to remove it.



37. REMOVE REAR SEAT RECLINING CONTROL NO. 2 CABLE


    B191128
  1. Cut the 2 cable ties and remove the rear seat reclining control No. 2 cable and rear seatback lock control No. 1 cable sub-assembly



38. REMOVE REAR SEAT CUSHION SPRING NO. 1


    B191129
  1. Remove the rear seat cushion spring.



39. REMOVE REAR NO. 1 SEAT ADJUSTER ASSEMBLY INNER RH


    B191126
  1. Disconnect the rear No. 1 seat lock cable assembly LH.

    HINT:
    1. The front nut is locked with adhesive. Loosen the rear nut to remove the cable.
    2. If the front nut becomes loose, adjust the length when installing the cable.

  1. Rotate the cable end to remove it.



    B191130
  1. Remove the 2 nuts and rear seat cushion support bracket.

  1. Remove the nut and rear No. 1 seat adjuster assembly.



40. REMOVE REAR SEATBACK ADJUSTER ASSEMBLY OUTER RH


    B191124
  1. Disconnect the rear No. 1 seat lock cable assembly RH.

    HINT:
    1. The front nut is locked with adhesive. Loosen the rear nut to remove the cable.
    2. If the front nut becomes loose, adjust the length when installing the cable.

  1. Rotate the cable end to remove it.



    B191131
  1. Remove the 3 nuts and rear No. 1 seat adjuster assembly.



41. REMOVE REAR SEAT TRACK ADJUSTING HANDLE RH


    B195232E01
  1. Slide the slide rail to the rearmost position.

  1. Using a small screwdriver, push down the handle stopper to disengage the claw and remove the adjusting handle.

    HINT:
    Insert the screwdriver in the hole shown in the illustration, while looking into the hole.