Home › Vehicle Interior › SEAT › REAR NO. 1 SEAT ASSEMBLY

REAR NO. 1 SEAT ASSEMBLY > REASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The procedure listed below is for the RH side.



1. INSTALL REAR SEAT TRACK ADJUSTING HANDLE RH


    B191132
  1. Install the rear seat track adjusting handle.

    HINT:
    Install the adjusting handle straight, and check that it is centered.



2. INSTALL REAR SEATBACK ADJUSTER ASSEMBLY OUTER RH


    B191131E01
  1. Install the rear seatback adjuster assembly with the nuts A, B and C in alphabetical order.

  1. Tighten nut A.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }

  1. Tighten nut B.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }

  1. Tighten nut C.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



    B191124
  1. Insert and rotate the cable end to connect it.

  1. Connect the rear No. 1 seat lock cable assembly.



    B195216E01
  1. Adjust the cable length.

    HINT:
    If the front nut became loose when the cable was removed, adjust the cable length.

    Specification 
    Area
    Measurement
    A
    51.5 to 53.7 mm (2.0276 to 2.1142 in)

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



3. INSTALL REAR NO. 1 SEAT ADJUSTER ASSEMBLY INNER RH


    B191130E01
  1. Install the rear No. 1 seat adjuster assembly and rear seat cushion support bracket with the nuts A, B and C in alphabetical order.

  1. Tighten nut A.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }

  1. Tighten nut B.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }

  1. Tighten nut C.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



    B191126
  1. Insert and rotate the cable end to connect it.

  1. Connect the rear No. 1 seat lock cable assembly.



    B195217E01
  1. Adjust the cable length.

    HINT:
    If the front nut became loose when the cable was removed, adjust the cable length.

    Specification 
    Area
    Measurement
    A
    51.5 to 53.7 mm (2.0276 to 2.1142 in)

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



4. INSTALL REAR SEAT CUSHION SPRING NO. 1


    B191129
  1. Install the rear seat cushion spring No. 1.



5. INSTALL REAR SEAT RECLINING CONTROL NO. 2 CABLE


    B191128
  1. Connect the rear seat reclining control No. 2 cable and rear seatback lock control No. 1 cable sub-assembly with 2 cable ties.



6. INSTALL REAR SEATBACK LOCK CONTROL NO. 2 CABLE SUB-ASSEMBLY


    B195214
  1. Insert and rotate the cable end to connect it.

  1. Connect the rear seatback lock control No. 2 cable sub-assembly and install the cable.



    B195215E01
  1. Adjust the cable length.

    HINT:
    If the front nut became loose when the cable was removed, adjust the cable length.

    Specification 
    Area
    Measurement
    A
    39.3 to 46.3 mm (1.5472 to 1.8228 in)

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



7. INSTALL REAR SEATBACK COVER RH


    B195213
  1. Install the rear seatback cover with the screw.



8. INSTALL REAR SEATBACK COVER LH


    B195212
  1. Install the rear seatback cover with the screw.

  1. Connect the cable with the cable clamp.



9. INSTALL REAR SEAT RECLINING COVER INNER


    B191121
  1. Install the rear seat reclining cover with the 2 screws.



10. INSTALL REAR SEAT RECLINING COVER INNER LH


    B191111
  1. Engage the guide to install the rear seat reclining cover.

  1. Install the screw.



11. INSTALL REAR BACK LOCK CONTROL LEVER SUB-ASSEMBLY RH


    B191119
  1. Install the rear back lock control lever sub-assembly and rear seat cushion lock striker sub-assembly with the 3 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. Using a T40 "TORX" socket, install the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }



12. INSTALL REAR SEAT CUSHION HOLDER BRACKET RH


    B200245
  1. Install the rear seat cushion holder bracket with the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



13. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY RH


    B191117
  1. Using a T40 "TORX" socket, install the rear seatback frame sub-assembly with the 5 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }



    B191116
  1. Connect the 2 cables.

    HINT:
    1. When installing the upper cable, operate the release pedal at the back of the seat to make it easier to connect the cable. However, be careful because the seatback will fall forward.
    2. Install the lower cable cap on the center groove.

  1. Bind the 3 cables with a cable tie.



    B191114
  1. Insert and rotate the cable ends to connect them.

  1. Connect the 2 clamps and install the cables.

    HINT:
    Install the cap on the center groove.



14. INSTALL REAR SEAT RECLINING COVER INNER RH


    B191112
  1. Engage the 3 claws to install the rear seat reclining cover.

  1. Install the screw.



    B191118
  1. Insert the cable through the rear seatback frame sub-assembly.



15. INSTALL REAR SEAT RECLINING COVER NO. 1 LH


    B191110
  1. Engage the guide to install the rear seat reclining cover.

  1. Install the screw.



16. INSTALL SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)


    B191093
  1. Set the seatback heater with the name stamp side facing the seatback cover.

  1. Install the seatback heater with new 8 tack pins.

    HINT:
    Do not bend or fold the seatback heater assembly.



17. INSTALL SEPARATE TYPE REAR SEATBACK COVER


    B191107E01
  1. Using hog ring pliers, install the seatback cover to the seatback pad with 8 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



18. INSTALL SEATBACK COVER WITH PAD


    B191104
  1. Engage the hooks to install the seatback cover with pad.



    B191103E01
  1. Using hog ring pliers, install the seatback cover to the seatback frame with 2 new hog rings.



19. INSTALL NO. 1 SEATBACK COVER SUB-ASSEMBLY RH


    B200244E01
  1. Engage the hooks.

  1. Using hog ring pliers, install the No. 1 seatback cover sub-assembly to the seatback frame with 2 new hog rings.



20. INSTALL REAR SEAT HEADREST SUPPORT


    B191134E01
  1. Align the protruding portion of the rear seat headrest supports with the installation grooves of the rear seatback frame.

  1. Engage the 4 claws to install the 2 supports.



21. INSTALL REAR SEAT CUSHION UNDER COVER RH


    B191097
  1. Install the rear seat cushion under cover with the 3 screws.



22. INSTALL REAR SEAT CUSHION HINGE COVER RH


    B191096
  1. Engage the 3 claws to install the rear seat cushion hinge cover.

  1. Install the 2 screws.



23. INSTALL REAR SEAT CUSHION HINGE COVER NO. 1


    B191095
  1. Engage the 4 claws and clip to install the rear seat cushion hinge cover.

  1. Install the screw.



24. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY RH


    B191101
  1. Engage the 7 clips and install the rear seatback board sub-assembly.



25. INSTALL SEAT ARMREST ASSEMBLY RH (w/ Armrest)


    B195222
  1. Install the seat armrest assembly with the bolt.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }



26. INSTALL REAR NO. 1 SEAT ARMREST CAP (w/ Armrest)


    B195221
  1. Engage the 3 claws and install the rear No. 1 seat armrest cap.



27. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH


    B191100E01
  1. Connect the cable in the order shown in the illustration to install the lock control lever sub-assembly.

  1. Install the rear seat lock control lever sub-assembly with the 2 screws.



28. INSTALL REAR SEATBACK LOCK STRIKER COVER


    B191099
  1. Engage the guide and claw to install the rear seatback lock striker cover.



29. INSTALL REAR SEAT HEADREST ASSEMBLY


30. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY RH


    B200248
  1. Connect the connector.

  1. Engage the 5 harness clamps and install the seat heater control sub-assembly.

  1. Fasten the harness and cable.



31. INSTALL NO. 1 SEAT CUSHION COVER RH


    B191122
  1. Engage the claw and install the No. 1 seat cushion cover.

  1. Install the 2 screws.

  1. Engage the cable clamp and connect the cable to the No. 1 seat cushion cover.



    B200249
  1. When installing the No. 1 seat cushion cover, pass the cable under the cover, as shown in the illustration.



32. INSTALL SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)


    B191109
  1. Set the seat cushion heater with the name stamp side facing the seat cushion cover.

  1. Install the seat cushion heater with new 31 tack pins.

    HINT:
    Do not bend or fold the seat cushion heater assembly.



33. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER


    B191108E01
  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 11 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



34. INSTALL REAR SEAT CUSHION SPRING ASSEMBLY RH (w/ Seat Heater System)


    B200247
  1. Engage the hooks to install the rear seat cushion spring assembly.



    B200242E01
  1. Using hog ring pliers, install the seat cushion spring with 9 new hog rings.



35. INSTALL REAR SEAT CUSHION SPRING ASSEMBLY RH (w/o Seat Heater System)


    B191092
  1. Engage the hooks to install the rear seat cushion spring assembly.



    B200242E01
  1. Using hog ring pliers, install the seat cushion spring with 9 new hog rings.



36. INSTALL REAR NO. 1 SEAT CUSHION ASSEMBLY RH


    B191091E01
  1. Install the 2 bushes to the cushion spring. Then, using a T45 "TORX" socket, install the 2 bolts.

    1. for Bolt A

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. Install the 2 bolts.

    1. for Bolt B

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



    B200240
  1. Fasten the cable to the seat cushion spring with 2 cable ties and connect the cable.

    HINT:
    Align the cable with the alignment marks on the seat cushion spring.



    B191089
  1. Fasten the cable with a cable tie.

  1. Engage the cable clamp and connect the cable to the seat cushion spring.



    B191088
  1. Fasten the cable to the seat cushion spring with a cable tie and connect the cable.



    B191090
  1. Connect the connector and engage the 3 harness clamps.

    HINT:
    If the vehicle is equipped with the seat heater system, connect the connector and engage the clamps.



37. INSTALL REAR SEAT INNER BELT ASSEMBLY


    B191087
  1. Install the rear seat inner belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



38. INSTALL REAR SEAT CUSHION HINGE COVER NO. 2


B191085
  1. Engage the 2 claws to install the rear seat cushion hinge cover.

  1. Install the screw.



39. INSTALL REAR SEAT CUSHION HINGE COVER NO. 3


B191084
  1. Engage the 2 claws to install the rear seat cushion hinge cover.

  1. Install the screw.



40. INSTALL REAR SEAT RECLINING RELEASE LEVER


    B191083
  1. Install the rear seat reclining release lever with the 3 screws.



41. INSTALL RECLINING ADJUSTER KNOB CAP RH


    B191082
  1. Engage the 3 claws and install the reclining adjuster knob cap.



    B200250E01
  1. Press the pink button on the rear seatback lock control No. 1 cable to release the cable lock, operate the lever a few times to adjust the amount of cable play, and then push in the pink button to lock the cable.