Home › Vehicle Interior › SEAT › REAR CENTER SEAT ASSEMBLY

REAR CENTER SEAT ASSEMBLY > REASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.



1. INSTALL REAR SEAT BRACKET


    B191187
  1. Install the rear seat bracket with the 2 nuts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



2. INSTALL REAR SEAT TRACK ADJUSTING HANDLE


    B191186
  1. Install the rear seat track adjusting handle.

    HINT:
    Install the adjusting handle straight, and check that it is centered.



3. INSTALL REAR NO. 1 SEAT ADJUSTER ASSEMBLY


    B191185E01
  1. Install the rear No. 1 seat adjuster assembly with nuts A, B and C in alphabetical order.

  1. Tighten nut A.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Tighten nut B.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }

  1. Tighten nut C.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



4. INSTALL REAR NO. 1 SEAT ADJUSTER SUB-ASSEMBLY


    B191184E01
  1. Install the rear No. 1 seat adjuster sub-assembly with nuts A, B and C in alphabetical order.

  1. Tighten nut A.

    Torque:
    32 N*m{ 326 kgf*cm , 31 ft.*lbf }

  1. Tighten nut B.

    Torque:
    32 N*m{ 326 kgf*cm , 31 ft.*lbf }

  1. Tighten nut C.

    Torque:
    32 N*m{ 326 kgf*cm , 31 ft.*lbf }



5. INSTALL REAR SEAT RECLINING CONTROL CABLE


    B191183
  1. Insert the cable through the center seatback frame sub-assembly.

  1. Insert and rotate the cable ends to connect them.

  1. Connect the 2 clamps and install the rear seat reclining control cable.



6. INSTALL CENTER SEATBACK FRAME SUB-ASSEMBLY


    B191182E01
  1. Using a T55 "TORX" socket, install the frame with the 2 bolts.

    1. for Bolt A

    Torque:
    80 N*m{ 816 kgf*cm , 59 ft.*lbf }

  1. Install the 2 bolts.

    1. for Bolt B

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }



7. INSTALL CENTER SEAT HINGE COVER


    B191180
  1. Engage the 2 claws to install the center seat hinge cover.

  1. Install the screw.



8. INSTALL CENTER SEAT HINGE COVER UPPER LH


    B191181
  1. Engage the 2 claws to install the center seat hinge cover.

  1. Install the 2 screws.



9. INSTALL CENTER SEAT OUTER BELT ASSEMBLY


    B191179E01
  1. Align the center seatback frame claws with the center seat outer belt retractor positioning holes.

  1. Install the center seat outer belt assembly with the 4 nuts.

    1. for Nut A

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    1. for Nut B

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Engage the cable with the cable tie.



10. INSTALL CENTER SEATBACK COVER SUB-ASSEMBLY


    B191178
  1. Install the center seatback cover sub-assembly to the center seatback pad.



11. INSTALL SEATBACK COVER WITH PAD


    B191175
  1. Engage the hooks to install the seatback cover with pad.



    B195220
  1. Engage the hooks.



    B195229E01
  1. Using hog ring pliers, install the center seatback cover to the center seatback frame with 6 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover
    2. When installing the hog rings, avoid wrinkling the cover.



    B191177E01
  1. Using hog ring pliers, install the center seatback cover to the center seatback frame with 5 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover
    2. When installing the hog rings, avoid wrinkling the cover.



12. INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY RH


    B191174
  1. Install the rear seatback hinge sub-assembly with the bolt.



13. INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY LH


    B191173
  1. Install the rear seatback hinge sub-assembly with the bolt.



14. INSTALL CENTER ARMREST HINGE COVER RH


    B191172
  1. To install the center armrest hinge cover RH, slide it rearward install the screw, as shown in the illustration.



15. INSTALL CENTER ARMREST HINGE COVER LH


    B191171
  1. To install the center armrest hinge cover LH, slide it rearward install the screw, as shown in the illustration.



16. INSTALL ARMREST ASSEMBLY


    B191167
  1. Install the armrest assembly with the 2 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



17. INSTALL REAR SEAT SHOULDER BELT HOLE COVER NO. 3


    B191168
  1. Engage the 2 claws, to the rear seat shoulder belt hole cover.

  1. Install the rear seat shoulder belt hole cover with the 2 screws.



18. INSTALL REAR SEAT HEADREST SUPPORT


    B191166E01
  1. Align the protruding portion of the rear seat headrest supports with the installation grooves of the center seatback frame.

  1. Engage the 4 claws to install the 2 rear seat headrest supports.



19. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH


    B191245E01
  1. Connect the cable in the order shown in the illustration to install the rear seat lock control lever sub-assembly.

  1. Install the rear seat lock control lever sub-assembly with the 2 screws.



20. INSTALL REAR SEATBACK LOCK STRIKER COVER


    B191164
  1. Engage the guide and claw to install the rear seatback lock striker cover.



21. INSTALL REAR SEAT SHOULDER BELT HOLE COVER NO. 2


    B191162
  1. Using a T30 "TORX" socket, install the rear seat shoulder belt hole cover with the 2 bolts.

    Torque:
    0.9 N*m{ 9.2 kgf*cm , 8.0 in.*lbf }



22. INSTALL REAR SEATBACK LOCK BEZEL UPPER


    B191161
  1. Install the rear seatback lock bezel upper with the 2 screws.



    B191159
  1. Install the center seat outer belt lower bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



23. INSTALL REAR SEAT SHOULDER BELT HOLE COVER NO. 1


    B191160
  1. Engage the 4 claws and install the rear seat shoulder belt hole cover.



24. INSTALL CENTER SEAT INNER BELT ASSEMBLY


    B191158
  1. Install center seat inner belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



25. INSTALL REAR SEAT CUSHION UNDER COVER


    B191157
  1. Install the rear seat cushion under cover with the 2 screws.



26. INSTALL CENTER SEAT HINGE COVER RH


    B191156
  1. Engage the 3 claws and clip to install the center seat hinge cover.

  1. Install the screw.



27. INSTALL CENTER SEAT HINGE COVER LH


    B191155
  1. Engage the 3 claws and clip to install the center seat hinge cover.

  1. Install the screw.



28. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY


    B191154
  1. Engage the 6 clips to install the rear seatback board sub-assembly.



29. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY


30. INSTALL CENTER SEAT CUSHION COVER SUB-ASSEMBLY


    B191153E01
  1. Using hog ring pliers, install the center seat cushion cover to the center seat cushion pad with 7 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover
    2. When installing the hog rings, avoid wrinkling the cover.



31. INSTALL REAR SEAT CUSHION SPRING ASSEMBLY


    B191151
  1. Engage the hooks and install the seat cushion spring assembly.



32. INSTALL CENTER SEAT CUSHION ASSEMBLY


B191150E01
  1. Install the 2 bushes to the cushion spring. Then, using a T45 "TORX" socket, install the 2 bolts.

    1. for Bolt A

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. Install the 2 bolts.

    1. for Bolt B

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



    B191149
  1. Engage the hook and loop fastener and hook.



33. INSTALL REAR SEAT CUSHION HINGE COVER UPPER RH


    B191148
  1. Engage the 2 claws and install the rear seat cushion hinge cover upper.

  1. Install the screw.

  1. Engage the hook.



34. INSTALL REAR SEAT CUSHION HINGE COVER UPPER LH


    B191147
  1. Engage the 2 claws and install the rear seat cushion hinge cover upper.

  1. Install the screw.

  1. Engage the hook.