Home › Vehicle Interior › SEAT › POWER SEAT SWITCH (for Rear No. 2 Seat)

POWER SEAT SWITCH (for Rear No. 2 Seat) > INSPECTION

for Preparation Click here



1. INSPECT REAR POWER SEAT SWITCH


E159000E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    5 (BACK) - 6 (E)
    BACK
    Below 1 Ω
    5 (BACK) - 6 (E)
    OFF
    10 kΩ or higher
    4 (FWD) - 6 (E)
    FWD
    Below 1 Ω
    4 (FWD) - 6 (E)
    OFF
    10 kΩ or higher

    If the result is not as specified, replace the switch.

  1. Apply battery voltage to the switch connector, and check that the rear power seat switch illuminates.

    OK:
    Measurement Condition
    Switch Condition
    Specified Condition
    Battery positive (+) → 6 (ILL+)
    Battery negative (-) → 1 (ILL-)
    Always
    Illuminates

    If the result is not as specified, replace the switch.



2. INSPECT FOLD SEAT SWITCH ASSEMBLY (for RH Side)


E158999E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3 (FOLD) - 5 (E)
    FOLD
    Below 1 Ω
    3 (FOLD) - 5 (E)
    OFF
    10 kΩ or higher
    4 (RETURN) - 5 (E)
    RETURN
    Below 1 Ω
    4 (RETURN) - 5 (E)
    OFF
    10 kΩ or higher

    If the result is not as specified, replace the switch.

  1. Apply battery voltage to the switch connector, and check that the fold seat switch assembly illuminates.

    OK:
    Measurement Condition
    Switch Condition
    Specified Condition
    Battery positive (+) → 2 (IND)
    Battery negative (-) → 5 (E)
    FOLD
    Indicator illuminates
    Battery positive (+) → 2 (IND)
    Battery negative (-) → 5 (E)
    RETURN
    Indicator illuminates
    Battery positive (+) → 1 (+B)
    Battery negative (-) → 5 (E)
    Always
    Lettering illuminates

    If the result is not as specified, replace the switch.



3. INSPECT FOLD SEAT SWITCH ASSEMBLY (for LH Side)


E158998E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    4 (FOLD) - 3 (E)
    FOLD
    Below 1 Ω
    4 (FOLD) - 3 (E)
    OFF
    10 kΩ or higher
    5 (RETURN) - 3 (E)
    RETURN
    Below 1 Ω
    5 (RETURN) - 3 (E)
    OFF
    10 kΩ or higher

    If the result is not as specified, replace the switch.

  1. Apply battery voltage to the switch connector, and check that the fold seat switch assembly illuminates.

    OK:
    Measurement Condition
    Switch Condition
    Specified Condition
    Battery positive (+) → 2 (IND)
    Battery negative (-) → 3 (E)
    FOLD
    Indicator illuminates
    Battery positive (+) → 2 (IND)
    Battery negative (-) → 3 (E)
    RETURN
    Indicator illuminates
    Battery positive (+) → 1 (+B)
    Battery negative (-) → 3 (E)
    Always
    Lettering illuminates

    If the result is not as specified, replace the switch.



4. INSPECT FOLD SEAT SWITCH ASSEMBLY (for Luggage Compartment RH Seat)


E158999E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3 (FOLD) - 5 (E)
    FOLD
    Below 1 Ω
    3 (FOLD) - 5 (E)
    OFF
    10 kΩ or higher
    4 (RETURN) - 5 (E)
    RETURN
    Below 1 Ω
    4 (RETURN) - 5 (E)
    OFF
    10 kΩ or higher

    If the result is not as specified, replace the switch.

  1. Apply battery voltage to the switch connector, and check that the fold seat switch assembly illuminates.

    OK:
    Measurement Condition
    Switch Condition
    Specified Condition
    Battery positive (+) → 2 (IND)
    Battery negative (-) → 5 (E)
    FOLD
    Indicator illuminates
    Battery positive (+) → 2 (IND)
    Battery negative (-) → 5 (E)
    RETURN
    Indicator illuminates
    Battery positive (+) → 1 (+B)
    Battery negative (-) → 5 (E)
    Always
    Lettering illuminates

    If the result is not as specified, replace the switch.



5. INSPECT FOLD SEAT SWITCH ASSEMBLY (for Luggage Compartment LH Seat)


E158998E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    4 (FOLD) - 3 (E)
    FOLD
    Below 1 Ω
    4 (FOLD) - 3 (E)
    OFF
    10 kΩ or higher
    5 (RETURN) - 3 (E)
    RETURN
    Below 1 Ω
    5 (RETURN) - 3 (E)
    OFF
    10 kΩ or higher

    If the result is not as specified, replace the switch.

  1. Apply battery voltage to the switch connector, and check that the fold seat switch assembly illuminates.

    OK:
    Measurement Condition
    Switch Condition
    Specified Condition
    Battery positive (+) → 2 (IND)
    Battery negative (-) → 3 (E)
    FOLD
    Indicator illuminates
    Battery positive (+) → 2 (IND)
    Battery negative (-) → 3 (E)
    RETURN
    Indicator illuminates
    Battery positive (+) → 1 (+B)
    Battery negative (-) → 3 (E)
    Always
    Lettering illuminates

    If the result is not as specified, replace the switch.