Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR CONTROL SWITCH (for Luggage Compartment)

POWER BACK DOOR CONTROL SWITCH (for Luggage Compartment) > INSTALLATION

for Preparation Click here



1. INSTALL BACK DOOR CONTROL SWITCH


    B192517
  1. Engage the 4 claws and install the back door control switch onto the No. 3 side trim base.



    B192515
  1. Engage the claw and install the No. 3 side trim base with back door control switch onto the rear window side garnish assembly LH.

  1. Install the screw.



2. INSTALL REAR WINDOW NO. 2 SIDE GARNISH ASSEMBLY LH


    B191798
  1. Connect the connector.

  1. Engage the 5 clips and install the rear window No. 2 side garnish assembly LH.

  1. Install the bolt.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



    B193892
  1. Engage the claw and install the cover.



3. INSTALL QUARTER TRIM PANEL ASSEMBLY LH


  1. Connect the connector.


    B190144

  1. Engage the 12 clips to install the quarter trim panel.

  1. Install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Engage the 2 clips.



    B193068
  1. Engage the 2 claws and install the cover.



    B191816
  1. Install the outer lap belt anchor with bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B191818
  1. Install the outer lap belt anchor with bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B193920
  1. Engage the 3 claws to install the outer lap belt anchor cover.



4. INSTALL QUARTER TRIM PANEL ASSEMBLY LH (for Power Seat)


  1. Connect the 5 connectors.


    B191800

  1. Engage the 12 clips to install the quarter trim panel.

  1. Install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Engage the 2 clamps and install the wire harness.

  1. Engage the 2 clips.



    B193068
  1. Engage the 2 claws and install the cover.



    B191816
  1. Install the outer lap belt anchor with bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B191818
  1. Install the outer lap belt anchor with bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B193920
  1. Engage the 3 claws to install the outer lap belt anchor cover.



5. INSTALL REAR FLOOR MAT SUPPORT PLATE


    B190142
  1. Engage the 5 clips and the 4 claws, and install the rear floor mat support plate.



6. INSTALL ROPE HOOK ASSEMBLY


    B190141
  1. Install the rope hook with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    B190139
  1. Engage the 2 claws and install the cover.



7. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure for both sides.



8. INSTALL REAR DOOR SCUFF PLATE LH

HINT:
Use the same procedure for both sides.



9. INSTALL REAR FLOOR STEP NO. 1 COVER


    B191404
  1. Engage the 2 claws and install the rear floor step No. 1 cover.



10. INSTALL REAR FLOOR STEP NO. 2 COVER


    B193890
  1. Engage the 2 claws and the install the rear floor step No. 2 cover.



11. INSTALL REAR SEAT CUSHION HINGE LOWER COVER LH

HINT:
Use the same procedure for both sides.



12. INSTALL REAR NO. 2 SEAT ASSEMBLY LH (for Manual Seat)
  1. Remove the rear No. 2 seat assembly LH (Click here).



13. INSTALL REAR NO. 2 SEAT ASSEMBLY LH (for Power Seat)
  1. Remove the rear No. 2 seat assembly LH (Click here).



14. INSTALL DECK BOARD BRACKET


    B190119
  1. Install the deck board bracket with the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



15. INSTALL DECK BOARD REINFORCEMENT SUB-ASSEMBLY


    B190120
  1. Install the deck board reinforcement with the 4 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



16. INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY


    B190117
  1. Engage the 5 clips and install the No. 1 deck board.



17. INSTALL ROPE HOOK ASSEMBLY


    B191405
  1. Install the rope hook with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    HINT:
    Use the same procedure for both sides.



18. INSTALL LUGGAGE COMPARTMENT TRIM BOX


    B190116
  1. Install the luggage compartment trim box with the 4 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



    B194633
  1. Install the 4 caps.



19. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY


    B194608
  1. Engage the 4 guides and install the No. 2 deck board.