Home › Drivetrain ยท A750F AUTOMATIC TRANSMISSION / TRANSAXLE › OIL COOLER

OIL COOLER > INSTALLATION

for Preparation Click here



1. INSTALL TRANSMISSION OIL COOLER ASSEMBLY (w/o Trailer Towing System)


    C157012E04
  1. Coat 2 new O-rings with ATF, and install them to the transmission oil cooler.

  1. Align the transmission oil cooler with the transmission oil cooler spacer and assemble them with the 3 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the 2 transmission oil cooler hoses to the transmission oil cooler spacer with the 2 clips.



    C161815E05
  1. Temporarily install the transmission oil cooler with transmission oil thermostat with bolt A.

  1. Install the bolt B and tighten it to the specified torque. Then tighten bolt A to the specified torque.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. Connect the 2 transmission oil cooler hoses with the 2 clips.

    HINT:
    Make sure the pinching portion of each clip is facing the direction shown in the illustration.



2. INSTALL TRANSMISSION OIL COOLER ASSEMBLY (w/ Trailer Towing System)


    C179291E02
  1. Coat 2 new O-rings with ATF, and install them to the transmission oil cooler.

  1. Align the transmission oil cooler with the transmission oil thermostat and assemble them with the 3 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the 2 transmission oil cooler hoses to the transmission oil thermostat with the 2 clips.



    C179294E01
  1. Temporarily install the transmission oil cooler with transmission oil thermostat with bolt A.

  1. Install the bolt B and tighten it to the specified torque. Then tighten bolt A to the specified torque.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. Connect the 2 transmission oil cooler hoses with the 2 clips.

    HINT:
    Make sure the pinching portion of each clip is facing the direction shown in the illustration.



    C155914
  1. Connect the 2 No. 2 transmission oil cooler hoses to the transmission oil thermostat.



3. CONNECT WATER BY-PASS PIPE ASSEMBLY


    C157031E03
  1. Connect the 2 water by-pass hoses with the 2 clips and install the water by-pass pipe with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    HINT:
    Make sure the pinching portion of each clip is facing the direction shown in the illustration.



4. INSTALL HOSE HEAT PROTECTOR


    C161816
  1. Install the hose heat protector with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }



5. INSTALL FRONT EXHAUST PIPE ASSEMBLY


    A185586
  1. Install the new gasket to the front exhaust pipe assembly.

  1. Install the front exhaust pipe assembly with the 3 new nuts.

    Torque:
    54 N*m{ 554 kgf*cm , 40 ft.*lbf }



    A185585
  1. Connect the heated oxygen sensor connector.



    A185584
  1. Connect the air fuel ratio sensor connector.



6. ADD ENGINE COOLANT
  1. Add engine coolant.

    Standard capacity:
    9.7 liters (10.3 US qts, 8.5 Imp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).
    2. The thermostat opening timing can be confirmed by pressing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.



    A151850E03
  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Install the reservoir cap.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Install the radiator cap.

  1. Start the engine and warm it up until the thermostat opens.

    HINT:
    The thermostat opening timing can be confirmed by pressing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. Maintain the engine speed at 2000 to 2500 rpm and warm up the engine until the cooling fan operates.

    NOTICE:
    1. Make sure that the radiator reservoir still has some coolant in it.
    2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
    3. If there is not enough coolant, the engine may burn out or overheat.

  1. Press the inlet and outlet radiator hoses several times by hand to bleed air.

    CAUTION:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the fan.

  1. Stop the engine, and wait until the engine coolant cools down.



    A151850E04
  1. If the coolant level is below the LOW line, repeat all of the procedures above.



7. ADD AUTOMATIC TRANSMISSION FLUID

Fluid type:
Toyota Genuine ATF WS

HINT:
Fill the transmission with the amount of fluid listed in the table below.

Standard Capacity:
Repair
Fill amount
Transmission pan and drain plug removal
1.7 liters (1.8 US qts, 1.5 Imp. qts)
Transmission valve body removal
4.3 liters (4.5 US qts, 3.8 Imp. qts)
Torque converter removal
5.4 liters (5.7 US qts, 4.8 Imp. qts)



8. ADJUST AUTOMATIC TRANSMISSION FLUID
  1. Adjust automatic transmission fluid (Click here).



9. INSPECT FOR AUTOMATIC TRANSMISSION FLUID LEAK


10. INSPECT FOR ENGINE COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A162054
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop. If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.



11. INSPECT FOR EXHAUST GAS LEAK