Home › Drivetrain ยท AB60F AUTOMATIC TRANSMISSION / TRANSAXLE › OIL COOLER

OIL COOLER > INSTALLATION

for Preparation Click here



1. INSTALL TRANSMISSION OIL COOLER ASSEMBLY (w/o Trailer Towing System)


    C161367E04
  1. Coat 4 new O-rings with ATF.

  1. Install the 4 O-rings, transmission oil cooler spacer and transmission oil cooler to the automatic transmission.

  1. Temporarily install the bolt A.

  1. Install the 2 bolts B and tighten them to the specified torque. Then tighten bolt A to the specified torque.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }



2. INSTALL TRANSMISSION OIL COOLER ASSEMBLY (w/ Trailer Towing System)


    C161366E04
  1. Coat 4 new O-rings with ATF.

  1. Install the 4 O-rings, transmission oil cooler thermostat and transmission oil cooler to the automatic transmission.

  1. Temporarily install the bolt A.

  1. Install the 2 bolts B and tighten them to the specified torque. Then tighten bolt A to the specified torque.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }



    C162129E03
  1. Connect the 2 No. 2 transmission oil cooler hoses to the transmission oil thermostat.

    HINT:
    1. Make sure the pinching portion of each clip is facing the direction shown in the illustration.
    2. Make sure the paint portion of each hose is facing outward.



3. CONNECT WATER BY-PASS PIPE ASSEMBLY


    C162140E03
  1. Connect the 2 water by-pass hoses with the 2 clips and install the water by-pass pipe with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    HINT:
    Make sure the pinching portion of each clip is facing the direction shown in the illustration.



4. INSTALL FRONT EXHAUST PIPE ASSEMBLY


A184929
  1. Install a new gasket and the front exhaust pipe to the exhaust manifold RH with 3 new nuts.

    Torque:
    54 N*m{ 554 kgf*cm , 40 ft.*lbf }

  1. Connect the air fuel ratio sensor connector.



5. ADD ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap. Then drain the coolant from the radiator.

  1. Loosen the 2 cylinder block drain cock plugs. Then drain the coolant from the engine.



  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    A151835E01

  1. Tighten the radiator drain cock plug by hand.



6. ADJUST AUTOMATIC TRANSMISSION FLUID
  1. Adjust automatic transmission fluid (Click here).



7. INSPECT FOR AUTOMATIC TRANSMISSION FLUID LEAK


8. INSPECT FOR ENGINE COOLANT LEAK


A161766E01

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.



9. INSPECT FOR EXHAUST GAS LEAK