Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM (w/ AVS)

DTC    C1762    Continuous Electric Current to Exhaust Solenoid

for Preparation Click here


DESCRIPTION


DTC Code
Detection Condition
Trouble Area
C1762
With the exhaust valve activated, the vehicle does not go down to the standard vehicle height after 105 seconds have elapsed.
  1. Clogging in the air tube or each valve
  2. Wire harness or connector
  3. Leveling solenoid valve (No. 2 height control valve)
  4. Gate solenoid valve (No. 2 height control valve)
  5. Exhaust solenoid valve (No. 1 height control compressor)
  6. Suspension control ECU

WIRING DIAGRAM


C179528E01


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (REAR GATE SOLENOID)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON, and turn the Techstream main switch on.

  1. Enter the following menus: Chassis / Air suspension / Active Test.

    Air Suspension 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Rear Gate Solenoid
    Gate solenoid valve/
    ON or OFF
    Operation sound of solenoid (clicking sound) can be heard

    OK:
    Operation of solenoid (clicking sound) can be heard



NG
REPLACE NO. 2 HEIGHT CONTROL VALVE SUB-ASSEMBLY (Click here)
OK


2.PERFORM ACTIVE TEST USING TECHSTREAM (REAR LEVELING SOLENOID)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON, and turn the Techstream main switch on.

  1. Enter the following menus: Chassis / Air suspension / Active Test.

    Air Suspension 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Rear Leveling Solenoid
    Leveling solenoid valve
    ON or OFF
    Operation sound of solenoid (clicking sound) can be heard

    OK:
    Operation of solenoid (clicking sound) can be heard



NG
REPLACE NO. 2 HEIGHT CONTROL VALVE SUB-ASSEMBLY (Click here)
OK


3.PERFORM ACTIVE TEST USING TECHSTREAM (EXHAUST SOLENOID)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON, and turn the Techstream main switch on.

  1. Enter the following menus: Chassis / Air suspension / Active Test.

    Air Suspension 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Exhaust Solenoid
    Exhaust solenoid valve
    ON or OFF
    Operation sound of solenoid (clicking sound) can be heard

    OK:
    Operation of solenoid (clicking sound) can be heard



NG
REPLACE NO. 1 HEIGHT CONTROL COMPRESSOR (Click here)
OK


4.INSPECT NO. 1 HEIGHT CONTROL COMPRESSOR (EXHAUST SOLENOID VALVE)
  1. Turn the ignition switch off.



    C165645E03
  1. Disconnect Q3 solenoid valve connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (B) - 2 (L)
    20°C (68°F)
    10 to 14 Ω

  1. Connect the battery positive (+) lead to terminal 1 and the negative (-) lead to terminal 2 of the solenoid valve connector. Then check that the valve makes an operating sound.

    OK:
    Operation of solenoid (clicking sound) can be heard



NG
REPLACE NO. 1 HEIGHT CONTROL COMPRESSOR (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (EXHAUST SOLENOID VALVE - ECU AND BODY GROUND)


    C179527E01
  1. Disconnect the O16 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Q3-1 (B) - O16-8 (SLEX)
    Always
    Below 1 Ω
    Q3-1 (B) or O16-8 (SLEX) - Body ground
    Always
    10 kΩ or higher
    Q3-2 (L) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SUSPENSION CONTROL ECU (Click here)