Home › Vehicle Interior › HEATING / AIR CONDITIONING › REAR EVAPORATOR TEMPERATURE SENSOR

REAR EVAPORATOR TEMPERATURE SENSOR > INSTALLATION

for Preparation Click here



1. INSTALL REAR EVAPORATOR TEMPERATURE SENSOR (NO. 2 AIR CONDITIONING HARNESS ASSEMBLY)


I104442
  1. Engage the clamp, claw and install the sensor.

  1. Connect the 2 connectors.



2. INSTALL REAR SIDE NO. 1 AIR DUCT


    I104303
  1. Install the air duct with the clip.

  1. Engage the clamp.



3. INSTALL COVER SUB-ASSEMBLY


    I104302
  1. Engage the 2 claws and install the cover.



4. INSTALL QUARTER TRIM BRACKET RH


    I104301
  1. Install the quarter trim bracket with the 2 bolts.

  1. Engage the clamp.



5. INSTALL REAR SIDE NO. 2 AIR DUCT


    I104300
  1. Install the air duct with the 2 clips.



6. INSTALL REAR WINDOW NO. 2 SIDE GARNISH ASSEMBLY RH


    B190123
  1. Engage the 5 clips and install the rear window No. 2 side garnish assembly RH.

  1. Install the bolt.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



    B193067
  1. Engage the claw and install the cover.



7. INSTALL QUARTER TRIM PANEL ASSEMBLY RH (for Standard)


  1. Connect the connector.


    B190143

  1. Engage the 12 clips and install the quarter trim panel assembly.

  1. Install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Engage the 2 clips.



    B190147
  1. Engage the 2 claws and install the cover.



    B190146
  1. Install the outer lap belt anchor with bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B190158
  1. Install the outer lap belt anchor with bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B190145
  1. Engage the 3 claws to install the outer lap belt anchor cover.



8. INSTALL QUARTER TRIM PANEL ASSEMBLY RH (for Power Seat)


  1. Connect the 3 connectors.


    B191799

  1. Engage the 12 clips to install the quarter trim panel.

  1. Install the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Engage the 2 clips.



    B190147
  1. Engage the 2 claws and install the cover.



    B190146
  1. Install the outer lap belt anchor with bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B190158
  1. Install the outer lap belt anchor with bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B190145
  1. Engage the 3 claws to install the outer lap belt anchor cover.



9. INSTALL REAR FLOOR MAT SUPPORT PLATE


    B190142
  1. Engage the 5 clips and the 4 claws, and install the rear floor mat support plate.



10. INSTALL ROPE HOOK ASSEMBLY


    B190141
  1. Install the rope hook with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    B190139
  1. Engage the 2 claws and install the cover.



11. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    B190154E01
  1. Align the location mark with the paint mark first, and install the rear door opening trim weatherstrip, as shown in the illustration.
    Paint Mark 
    Area
    Color
    RH side
    Pink
    LH side
    Purple



12. INSTALL REAR DOOR SCUFF PLATE RH


    B186666
  1. Engage the 2 claws and 5 clips to install the rear door scuff plate.

  1. Install the 2 bolts.



    B186665
  1. Engage the 6 claws and the 5 clips and the 2 guides, and install the rear door scuff plate.

  1. Install the screw.



13. INSTALL REAR FLOOR STEP NO. 1 COVER


    B191404
  1. Engage the 2 claws and install the rear floor step No. 1 cover.



14. INSTALL REAR FLOOR STEP NO. 2 COVER


    B193890
  1. Engage the 2 claws and the install the rear floor step No. 2 cover.



15. INSTALL REAR SEAT CUSHION HINGE LOWER COVER RH


    B191794
  1. Engage the 2 clips and the 5 claws, and install the rear cushion hinge lower cover RH.



16. INSTALL REAR NO. 2 SEAT ASSEMBLY RH (for Power Seat)
  1. Install the rear No. 2 seat assembly RH.

    NOTICE:
    Be careful not to damage the vehicle body.



    B191204
  1. Insert the 2 locating pins through the 2 body holes and make sure that the inner and outer seat tracks are locked securely.

  1. Install the 2 bolts.

    Torque:
    37 N*m{ 374 kgf*cm , 27 ft.*lbf }

  1. Connect the seat wire connector.



    B191200
  1. Install the 2 bolts.

    Torque:
    37 N*m{ 374 kgf*cm , 27 ft.*lbf }



17. INSTALL REAR NO. 2 SEAT ASSEMBLY RH (for Manual Seat)
  1. Install the rear No. 2 seat assembly RH.

    NOTICE:
    Be careful not to damage the vehicle body.



    B191202
  1. Insert the 2 locating pins through the 2 body holes and make sure that the inner and outer seat tracks are locked securely.

  1. Install the 2 bolts.

    Torque:
    37 N*m{ 374 kgf*cm , 27 ft.*lbf }



    B191200
  1. Install the 2 bolts.

    Torque:
    37 N*m{ 374 kgf*cm , 27 ft.*lbf }



18. INSTALL SEAT TRACK BRACKET FRONT COVER INNER


    B191199E01
  1. Engage the 2 guides and claw and clip in the order shown in the illustration, and then install the seat track bracket front cover inner.



19. INSTALL SEAT TRACK BRACKET FRONT COVER OUTER


    B191197E01
  1. Engage the 2 guides and 2 claws in the order shown in the illustration, and then install the seat track bracket front cover outer.



20. INSTALL DECK BOARD BRACKET


    B190119
  1. Install the deck board bracket with the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



21. INSTALL DECK BOARD REINFORCEMENT SUB-ASSEMBLY


    B190120
  1. Install the deck board reinforcement with the 4 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



22. INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY


    B190117
  1. Engage the 5 clips and install the No. 1 deck board.



23. INSTALL ROPE HOOK ASSEMBLY


    B191405
  1. Install the rope hook with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    HINT:
    Use the same procedure for both sides.



24. INSTALL LUGGAGE COMPARTMENT TRIM BOX


    B190116
  1. Install the luggage compartment trim box with the 4 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



    B194633
  1. Install the 4 caps.



25. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY


    B194608
  1. Engage the 4 guides and install the No. 2 deck board.