Home › Vehicle Interior › HEATING / AIR CONDITIONING › REAR EVAPORATOR TEMPERATURE SENSOR

REAR EVAPORATOR TEMPERATURE SENSOR > REMOVAL

for Preparation Click here



1. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY


    B190118
  1. Raise the handle, disengage the 4 guides and remove the No. 2 deck board.



2. REMOVE LUGGAGE COMPARTMENT TRIM BOX


    B194633
  1. Remove the 4 caps.



    B190116
  1. Remove the 4 bolts and the luggage compartment trim box.



3. REMOVE ROPE HOOK ASSEMBLY


    B191405
  1. Remove the bolt and the rope hook.

    HINT:
    Use the same procedure for both sides.



4. REMOVE NO. 1 DECK BOARD SUB-ASSEMBLY


    B190117
  1. Disengage the 5 clips and remove the No. 1 deck board.



5. REMOVE DECK BOARD REINFORCEMENT SUB-ASSEMBLY


    B190120
  1. Remove the 4 bolts and the deck board reinforcement.



6. REMOVE DECK BOARD BRACKET


    B190119
  1. Remove the 2 bolts and the deck board bracket.



7. REMOVE SEAT TRACK BRACKET FRONT COVER OUTER


    B191196E01
  1. Disengage the 2 claws and 2 guides in the order shown in the illustration, and then remove the seat track bracket front cover outer.



8. REMOVE SEAT TRACK BRACKET FRONT COVER INNER


    B191198E01
  1. Disengage the claw and clip and 2 guides in the order shown in the illustration, and then remove the seat track bracket front cover inner.



9. REMOVE REAR NO. 2 SEAT ASSEMBLY RH (for Power Seat)


    B191200
  1. Remove the 2 bolts.



    B191203
  1. Remove the 2 bolts.

  1. Remove the connector.

  1. Remove the rear No. 2 seat assembly RH.

    NOTICE:
    Be careful not to damage the vehicle body.



10. REMOVE REAR NO. 2 SEAT ASSEMBLY RH (for Manual Seat)


    B191200
  1. Remove the 2 bolts.



    B191201
  1. Remove the 2 bolts.

  1. Remove the rear No. 2 seat assembly RH.

    NOTICE:
    Be careful not to damage the vehicle body.



11. REMOVE REAR SEAT CUSHION HINGE LOWER COVER RH


    B191794
  1. Disengage the 2 clips and the 5 claws, and remove the rear seat cushion hinge lower cover.



12. REMOVE REAR FLOOR STEP NO. 1 COVER


    B191403E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the cap.

    HINT:
    Use the same procedure for both sides.



13. REMOVE REAR FLOOR STEP NO. 2 COVER


    B193052E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the cap.

    HINT:
    Use the same procedure for both sides.



14. REMOVE REAR DOOR SCUFF PLATE RH


    B186665
  1. Remove the bolt.

  1. Disengage the 5 clips and the 6 claws and 2 guides, and remove the rear door scuff plate front side.



    B186666
  1. Remove the 2 bolts.

  1. Disengage the 5 clips and the 2 claws, and remove the scuff plate rear side.



15. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH


    B191804
  1. Remove the rear door opening weatherstrip.



16. REMOVE ROPE HOOK ASSEMBLY

HINT:
Use the same procedure for both sides.



    B190140E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the cover.



    B190141
  1. Remove the bolt and the rope hook.



17. REMOVE REAR FLOOR MAT SUPPORT PLATE


    B190142
  1. Disengage the 5 clips and the 4 claws and remove the rear floor mat support plate.



18. REMOVE QUARTER TRIM PANEL ASSEMBLY RH (for Standard)


    B190145
  1. Disengage the 3 claws and remove the outer lap belt anchor cover.



    B190158
  1. Remove the bolt and outer lap belt anchor.



    B190146
  1. Remove the bolt and outer lap belt anchor.



    B190148E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the cover.



  1. Remove the 2 bolts.


    B190143

  1. Disengage the 14 clips.

  1. Disconnect the connector and remove the quarter trim panel.



19. REMOVE QUARTER TRIM PANEL ASSEMBLY RH (for Power Seat)


    B190145
  1. Disengage the 3 claws and remove the outer lap belt anchor cover.



    B190158
  1. Remove the bolt and outer lap belt anchor.



    B190146
  1. Remove the bolt and outer lap belt anchor.



    B190148E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the cover.



  1. Remove the 2 bolts.


    B191799

  1. Disengage the 14 clips.

  1. Disconnect the 3 connectors and remove the quarter trim panel.



20. REMOVE REAR WINDOW NO. 2 SIDE GARNISH ASSEMBLY RH


    B190122E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the cover.



    B190123
  1. Remove the bolt.

  1. Disengage the 5 clips.

  1. Pass the rear seat outer belt floor anchor through the rear window No. 2 side garnish, and remove the rear window No. 2 side garnish.



21. REMOVE REAR SIDE NO. 2 AIR DUCT


    I104300
  1. Remove the 2 clips and the air duct.



22. REMOVE QUARTER TRIM BRACKET RH


    I104301
  1. Disengage the clamp.

  1. Remove the 2 bolts and the quarter trim bracket.



23. REMOVE COVER SUB-ASSEMBLY


    I104302
  1. Disengage the 2 claws and remove the cover.



24. REMOVE REAR SIDE NO. 1 AIR DUCT


    I104303
  1. Disengage the clamps.

  1. Remove the clip and the air duct.



25. REMOVE REAR EVAPORATOR TEMPERATURE SENSOR (NO. 2 AIR CONDITIONING HARNESS ASSEMBLY)


I104442
  1. Disconnect the 2 connectors.

  1. Disengage the clamp, claw and the sensor.