REAR NO. 2 SEAT ASSEMBLY (for Power Seat Type LH Side) > DISASSEMBLY |
| 1. REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY LH |
![]() |
Remove the 2 clips.
![]() |
Remove the bolt and rear No. 2 seat inner belt assembly.
| 2. REMOVE REAR SEAT LOCK COVER OUTER LH |
![]() |
Remove the screw.
Disengage the 2 claws and remove the rear seat lock cover outer.
| 3. REMOVE REAR SEAT LOCK COVER INNER RH |
![]() |
Remove the screw.
Disengage the 3 claws and remove the rear seat lock cover inner.
| 4. REMOVE REAR NO. 2 SEAT CUSHION ASSEMBLY LH |
![]() |
Remove the 2 bolts.
Using a T45 "TORX" socket, remove the 2 bolts and 2 bushes. Then remove the rear No. 2 seat cushion assembly.
| 5. REMOVE NO. 3 SEAT CUSHION SPRING ASSEMBLY LH |
![]() |
Remove the 7 hog rings.
![]() |
Remove the hooks and No. 3 seat cushion spring assembly.
| 6. REMOVE NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY LH |
![]() |
Remove the 13 hog rings and No. 2 seat cushion cover sub-assembly.
| 7. REMOVE REAR SEAT CUSHION COVER LH |
![]() |
Remove the screw.
Disengage the claw and remove the rear seat cushion cover.
| 8. REMOVE REAR SEAT CUSHION COVER INNER RH |
![]() |
Remove the screw.
Disengage the claw and remove the rear seat cushion cover.
| 9. REMOVE REAR CENTER SEAT HEADREST ASSEMBLY |
| 10. REMOVE REAR SEAT HEADREST ASSEMBLY |
| 11. REMOVE REAR NO. 2 SEATBACK COVER LH |
![]() |
Disengage the 3 claws and remove the rear No. 2 seatback cover.
| 12. REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY LH |
![]() |
Disengage the 12 clips and remove the rear seatback board sub-assembly.
| 13. REMOVE REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY |
![]() |
Disengage the 8 claws and remove the 4 rear No. 2 seat headrest supports.
| 14. REMOVE SEATBACK COVER WITH PAD |
![]() |
Disengage the 2 wire harness clamps.
Disengage the hooks and remove the seatback cover with pad.
![]() |
Remove the clip and rear seat belt hook.
Remove the hog ring and seatback cover with pad.
| 15. REMOVE NO. 2 SEATBACK COVER SUB-ASSEMBLY LH |
![]() |
Remove the 16 hog rings and No. 2 seatback cover from the seatback pad.
| 16. REMOVE REAR SEAT WIRE HARNESS NO. 2 |
![]() |
Disconnect the 3 connectors.
Disengage the 4 wire harness clamps and remove the rear seat wire harness No. 2.
| 17. REMOVE RECLINING CONTROL BASE LH |
![]() |
Remove the 2 nuts and reclining control base.
| 18. REMOVE NO. 3 SEATBACK FRAME SUB-ASSEMBLY LH |
![]() |
Remove the 3 bolts and No. 3 seatback frame sub-assembly.
| 19. REMOVE POWER SEAT MOTOR ASSEMBLY RH |
![]() |
Using a screwdriver, remove the 2 washers.
![]() |
Using a screwdriver and hammer, lightly tap the reclining connecting pipe to remove it.
![]() |
Remove the 3 bolts and power seat motor assembly.
| 20. REMOVE POWER SEAT MOTOR ASSEMBLY LH |
![]() |
Remove the 3 bolts and power seat motor assembly.
| 21. REMOVE REAR NO. 2 SEAT ROD SUB-ASSEMBLY |
![]() |
Remove the 2 bolts and No. 2 seat rod sub-assembly.