Home › Vehicle Interior › SEAT › REAR NO. 2 SEAT ASSEMBLY (for Power Seat Type LH Side)

REAR NO. 2 SEAT ASSEMBLY (for Power Seat Type LH Side) > REASSEMBLY

for Preparation Click here


NOTICE:
Wear protective gloves. Sharp areas on the parts may injure your hands.



1. INSTALL REAR NO. 2 SEAT ROD SUB-ASSEMBLY


    B194032
  1. Install the No. 2 seat rod sub-assembly with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



2. INSTALL POWER SEAT MOTOR ASSEMBLY LH


    B201580
  1. Fully rotate both lower arms in the seat-folded direction, as shown in the illustration.

    NOTICE:
    If the motor is installed with the lower arms at an intermediate position, the motor initial position will not match the seat position, so that when the seat is operated the position will be incorrect.



    B201581
  1. Install the power seat motor with the 3 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



3. INSTALL POWER SEAT MOTOR ASSEMBLY RH


    B201582
  1. Install the power seat motor with the 3 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



    B201583
  1. Using a screwdriver and hammer, lightly tap the reclining connecting pipe to install it.

  1. Install the 2 washers.

    NOTICE:
    When the reclining connecting pipe extends about the same distance left and right, install the 2 washers.



    B201584
  1. Hold the reclining connecting pipe with pliers or similar tool and rotate the reclining connecting pipe and arms to the position shown in the illustration.



4. INSTALL NO. 3 SEATBACK FRAME SUB-ASSEMBLY LH


    B194028
  1. Install the No. 3 seatback frame with the 3 bolts.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



5. INSTALL RECLINING CONTROL BASE LH


    B194027
  1. Install the reclining control base with the 2 nuts.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



6. INSTALL REAR SEAT WIRE HARNESS NO. 2


    B194024
  1. Engage the 4 wire harness clamps.

  1. Connect the 3 connectors and install the rear seat wire harness No. 2.



7. INSTALL NO. 2 SEATBACK COVER SUB-ASSEMBLY LH


    B194023E01
  1. Using hog ring pliers, install the No. 2 seatback cover to the seatback pad with 16 new hog rings.



8. INSTALL SEATBACK COVER WITH PAD


    B194020E01
  1. Engage the clip and install the rear seat belt hook.

  1. Using hog ring pliers, install the seatback cover with pad to the seatback frame with a new hog ring.



    B194021
  1. Engage the hooks and install the seatback cover with pad.

  1. Engage the 2 wire harness clamps.



9. INSTALL REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY


    B194015E01
  1. Align the protruding portion of the rear No. 2 seat headrest supports with the installation grooves of the rear No. 2 seatback frame.

  1. Engage the 8 claws and install the 4 rear No. 2 seat headrest supports.



10. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH


    B194009
  1. Engage the 12 clips and install the rear seatback board sub-assembly.



11. INSTALL REAR NO. 2 SEATBACK COVER LH


    B195227
  1. Engage the 3 claws and install the rear No. 2 seatback cover.



12. INSTALL REAR SEAT HEADREST ASSEMBLY


13. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY


14. INSTALL REAR SEAT CUSHION COVER LH


    B194006
  1. Engage the claw and install the rear seat cushion cover.

  1. Install the screw.



15. INSTALL REAR SEAT CUSHION COVER INNER RH


    B194007
  1. Engage the claw and install the rear seat cushion cover.

  1. Install the screw.



16. INSTALL NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY LH


    B194005E01
  1. Using hog ring pliers, install the No. 2 seat cushion cover to the seat cushion pad with 13 new hog rings.



17. INSTALL NO. 3 SEAT CUSHION SPRING ASSEMBLY LH


    B194003
  1. Engage the hooks.



    B194002E01
  1. Using hog ring pliers, install the No. 3 seat cushion spring to the seat cushion cover with 7 new hog rings.



18. INSTALL REAR NO. 2 SEAT CUSHION ASSEMBLY LH


B194000E01
  1. Install the 2 bushes to the cushion spring. Then using a T45 "TORX" socket, install the 2 bolts.

    1. for Bolt A

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. Install the 2 bolts.

    1. for Bolt B

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



19. INSTALL REAR SEAT LOCK COVER OUTER LH


    B193996
  1. Engage the 2 claws and install the rear seat lock cover outer.

  1. Install the screw.



20. INSTALL REAR SEAT LOCK COVER INNER RH


    B193998
  1. Engage the 3 claws and install the rear seat lock cover inner.

  1. Install the screw.



21. INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY LH


    B193995
  1. Install the rear No. 2 seat inner belt assembly.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B193994
  1. Install the 2 clips.