Home › Vehicle Interior › SEAT › REAR NO. 2 SEAT ASSEMBLY (for Manual Seat Type RH Side)

REAR NO. 2 SEAT ASSEMBLY (for Manual Seat Type RH Side) > REASSEMBLY

for Preparation Click here


NOTICE:
Wear protective gloves. Sharp areas on the parts may injure your hands.



1. INSTALL REAR NO. 2 SEAT ROD SUB-ASSEMBLY


    B191244
  1. Install the No. 2 seat rod sub-assembly with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



2. INSTALL NO. 3 SEATBACK FRAME SUB-ASSEMBLY RH


    B191240
  1. Install the No. 3 seatback frame with the 5 bolts.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



3. INSTALL REAR NO. 1 SEAT LOCK CABLE ASSEMBLY


    B191238
  1. Insert the cable through the No. 3 seatback frame sub-assembly.

  1. Insert and rotate the cable ends to connect them.

  1. Connect the 2 clamps.

  1. Install the cable with the 3 cable ties.



4. INSTALL REAR SEAT RECLINING COVER INNER LH


    B191236
  1. Engage the claw and install the rear seat reclining cover.

  1. Install the screw.



5. INSTALL REAR SEAT RECLINING COVER INNER RH


    B191235
  1. Engage the claw and install the rear seat reclining cover.

  1. Install the screw.



6. INSTALL NO. 2 SEATBACK COVER SUB-ASSEMBLY RH


    B191232E01
  1. Using hog ring pliers, install the No. 2 seatback cover to the seatback pad with 13 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



7. INSTALL SEATBACK COVER WITH PAD


    B191227
  1. Engage the hooks and install the seatback cover with pad.



    B195219
  1. Engage the hooks.



8. INSTALL REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY


    B191224E01
  1. Align the protruding portion of the rear No. 2 seat headrest supports with the installation grooves of the rear No. 2 seatback frame.

  1. Engage the 4 claws and install the 2 rear No. 2 seat headrest supports.



9. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY RH


    B191222
  1. Engage the 9 clips and install the rear seatback board sub-assembly.



10. INSTALL REAR BACK LOCK CONTROL LEVER SUB-ASSEMBLY RH


    B191220E01
  1. Connect the cable in the order shown in the illustration to install the rear back control lever sub-assembly.

  1. Install the rear back control lever sub-assembly with the screw.



11. INSTALL REAR NO. 2 SEAT HANDLE


    B191219E01
  1. Connect the cable in the order shown in the illustration to install the rear No. 2 seat handle.

  1. Install the rear No. 2 seat handle with the 2 screws.



12. INSTALL REAR SEAT HEADREST ASSEMBLY


13. INSTALL REAR SEAT CUSHION COVER LH


    B191218
  1. Engage the claw and install the rear seat cushion cover.

  1. Install the screw.



14. INSTALL REAR SEAT CUSHION COVER OUTER RH


    B191217
  1. Engage the claw and install the rear seat cushion cover.

  1. Install the screw.



15. INSTALL NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY RH


    B191216E02
  1. Using hog ring pliers, install the No. 2 seat cushion cover to the seat cushion pad with 10 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



16. INSTALL NO. 3 SEAT CUSHION SPRING ASSEMBLY RH


    B191214
  1. Engage the hooks.



    B191213E01
  1. Using hog ring pliers, install the No. 3 seat cushion spring to the seat cushion cover with 5 new hog rings.



17. INSTALL REAR NO. 2 SEAT CUSHION ASSEMBLY RH


B191211E01
  1. Install the 2 bushes to the cushion spring. Then using a T45 "TORX" socket, install the 2 bolts.

    1. for Bolt A

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. Install the 2 bolts.

    1. for Bolt B

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



18. INSTALL REAR SEAT LOCK COVER OUTER RH


    B191209
  1. Engage the 2 claws and install the rear seat lock cover outer.

  1. Install the screw.



19. INSTALL REAR SEAT LOCK COVER INNER LH


    B191207
  1. Engage the 3 claws and install the rear seat lock cover inner.

  1. Install the screw.



20. INSTALL REAR NO. 2 SEAT INNER BELT SUB-ASSEMBLY


    B191206
  1. Install the rear No. 2 seat inner belt sub-assembly.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B191205
  1. Install the 2 clips.