REAR NO. 2 SEAT ASSEMBLY (for Power Seat Type RH Side) > REASSEMBLY |
| 1. INSTALL REAR NO. 2 SEAT ROD SUB-ASSEMBLY |
![]() |
Install the No. 2 seat rod sub-assembly with the 2 bolts.
| 2. INSTALL POWER SEAT MOTOR ASSEMBLY LH |
![]() |
Fully rotate both lower arms in the seat-folded direction, as shown in the illustration.
![]() |
Install the power seat motor with the 3 bolts.
| 3. INSTALL POWER SEAT MOTOR ASSEMBLY RH |
![]() |
Install the power seat motor with the 3 bolts.
![]() |
Using a screwdriver and hammer, lightly tap the reclining connecting pipe to install it.
Install the 2 washers.
![]() |
Hold the reclining connecting pipe with pliers or similar tool and rotate the reclining connecting pipe and arms to the position shown in the illustration.
| 4. INSTALL NO. 3 SEATBACK FRAME SUB-ASSEMBLY RH |
![]() |
Install the No. 3 seatback frame with the 5 bolts.
| 5. INSTALL RECLINING CONTROL BASE RH |
![]() |
Install the reclining control base with the 2 nuts.
| 6. INSTALL REAR SEAT WIRE HARNESS NO. 2 |
![]() |
Engage the 4 wire harness clamps.
Connect the 3 connectors and install the rear seat wire harness No. 2.
| 7. INSTALL NO. 2 SEATBACK COVER SUB-ASSEMBLY RH |
![]() |
Using hog ring pliers, install the No. 2 seatback cover to the seatback pad with 13 new hog rings.
| 8. INSTALL SEATBACK COVER WITH PAD |
![]() |
Engage the hooks and install the seatback cover with pad.
Engage the 2 wire harness clamps.
| 9. INSTALL REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY |
![]() |
Align the protruding portion of the rear No. 2 seat headrest supports with the installation grooves of the rear No. 2 seatback frame.
Engage the 4 claws and install the 2 rear No. 2 seat headrest supports.
| 10. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY RH |
![]() |
Engage the 9 clips and install the rear seatback board sub-assembly.
| 11. INSTALL REAR SEAT HEADREST ASSEMBLY |
| 12. INSTALL REAR SEAT CUSHION COVER LH |
![]() |
Engage the claw and install the rear seat cushion cover.
Install the screw.
| 13. INSTALL REAR SEAT CUSHION COVER OUTER RH |
![]() |
Engage the claw and install the rear seat cushion cover.
Install the screw.
| 14. INSTALL NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY RH |
![]() |
Using hog ring pliers, install the No. 2 seat cushion cover to the seat cushion pad with 10 new hog rings
| 15. INSTALL NO. 3 SEAT CUSHION SPRING ASSEMBLY RH |
![]() |
Engage the hooks.
![]() |
Using hog ring pliers, install the No. 3 seat cushion spring to the seat cushion cover with 5 new hog rings.
| 16. INSTALL REAR NO. 2 SEAT CUSHION ASSEMBLY RH |
![]() |
Install the 2 bushes to the cushion spring. Then using a T45 "TORX" socket, install the 2 bolts.
Install the 2 bolts.
| 17. INSTALL REAR SEAT LOCK COVER INNER LH |
![]() |
Engage the 3 claws and install the rear seat lock cover inner.
Install the screw.
| 18. INSTALL REAR SEAT LOCK COVER OUTER RH |
![]() |
Engage the 2 claws and install the rear seat lock cover outer.
Install the screw.
| 19. INSTALL REAR NO. 2 SEAT INNER BELT SUB-ASSEMBLY |
![]() |
Install the rear No. 2 seat inner belt sub-assembly.
![]() |
Install the 2 clips.