REAR NO. 1 SEAT OUTER BELT ASSEMBLY > REMOVAL |
| 1. REMOVE REAR NO. 2 SEAT ASSEMBLY RH (for Manual Seat) |
Remove the rear No. 2 seat assembly (Click here).
| 2. REMOVE REAR NO. 2 SEAT ASSEMBLY RH (for Power Seat) |
Remove the rear No. 2 seat assembly (Click here).
| 3. REMOVE REAR SEAT CUSHION HINGE LOWER COVER RH |
![]() |
Disengage the 2 clips and the 5 claws, and remove the rear seat cushion hinge lower cover.
| 4. REMOVE REAR FLOOR STEP NO. 1 COVER |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the cap.
| 5. REMOVE REAR FLOOR STEP NO. 2 COVER |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the cap.
| 6. REMOVE REAR DOOR SCUFF PLATE RH |
![]() |
Remove the bolt.
Disengage the 5 clips and the 6 claws and 2 guides, and remove the rear door scuff plate front side.
![]() |
Remove the 2 bolts.
Disengage the 5 clips and the 2 claws, and remove the scuff plate rear side.
| 7. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Remove the rear door opening weatherstrip.
| 8. REMOVE ROPE HOOK ASSEMBLY |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the cover.
![]() |
Remove the bolt and the rope hook.
| 9. REMOVE REAR FLOOR MAT SUPPORT PLATE |
![]() |
Disengage the 5 clips and the 4 claws and remove the rear floor mat support plate.
| 10. REMOVE QUARTER TRIM PANEL ASSEMBLY RH (for Manual Seat) |
![]() |
Disengage the 3 claws and remove the outer lap belt anchor cover.
![]() |
Remove the bolt and outer lap belt anchor.
![]() |
Remove the bolt and outer lap belt anchor.
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the cover.
Remove the 2 bolts.

Disengage the 14 clips.
Disconnect the connector and remove the quarter trim panel.
| 11. REMOVE QUARTER TRIM PANEL ASSEMBLY RH (for Power Seat) |
![]() |
Disengage the 3 claws and remove the outer lap belt anchor cover.
![]() |
Remove the bolt and outer lap belt anchor.
![]() |
Remove the bolt and outer lap belt anchor.
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the cover.
Remove the 2 bolts.

Disengage the 14 clips.
Disconnect the 3 connectors and remove the quarter trim panel.
| 12. REMOVE REAR WINDOW SIDE GARNISH ASSEMBLY RH |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the cover.
![]() |
Remove the bolt.
Detach the 5 clips.
Pass the rear seat outer belt floor anchor through the rear window side garnish, and remove the rear window side garnish.
| 13. REMOVE REAR SIDE NO. 2 AIR DUCT |
![]() |
Remove the 2 clips and the air duct.
| 14. REMOVE REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH |
![]() |
Remove the bolt.
![]() |
Remove the 2 bolts and rear No. 1 seat outer belt assembly.
| 15. REMOVE REAR NO. 1 SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY |
![]() |
Remove the 2 bolts and rear No. 1 shoulder belt anchor adjuster assembly.