Home › Engine / Hybrid System ยท 3UR-FE › ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > FAIL-SAFE CHART

for Preparation Click here


If any of the following DTCs are set, the ECM enters fail-safe mode to allow the vehicle to be driven temporarily.

DTC
Component
Fail-Safe Operation
Fail-Safe Deactivation Condition
P0011, P0021, P0015 and P0025
VVT system
  1. Idle up (Control of combustion worsening)
  2. Stopping fuel-cut control
Pass condition detected
P0031, P0032, P0051 and P0052
Air-Fuel Ratio (A/F) Sensor Heater
ECM turns off A/F sensor heater.
Ignition switch off
P0037, P0038, P0057 and P0058
Heated Oxygen (HO2) Sensor Heater
ECM turns off HO2 sensor heater.
Ignition switch off
P0102 and P0103
Mass Air Flow (MAF) Meter
ECM calculates ignition timing according to engine speed and throttle valve position.
Pass condition detected
P0112 and P0113
Intake Air Temperature (IAT) Sensor
ECM estimates IAT to be 20°C (68°F).
Pass condition detected
P0115, P0117 and P0118
Engine Coolant Temperature (ECT) Sensor
ECM estimates ECT to be 80°C (176°F).
Pass condition detected
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P0604, P0606, P060A, P060B, P060D, P060E, P0657, P2102, P2103, P2111, P2112, P2118, P2119 and P2135
Electronic Throttle Control System (ETCS)
ECM cuts off throttle actuator current and throttle valve returned to 7° throttle position by return spring.
ECM then adjusts engine output by controlling fuel injection (intermittent fuel-cut) and ignition timing in accordance with accelerator pedal opening angle to allow vehicle to continue at minimal speed*1.
Pass condition detected and then ignition switch turned off
P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and P0308*2
  1. Fuel injector
  2. Electronic Throttle Control System (ETCS)
When misfire occurs, fuel cut is performed for catalyst overheat malfunction prevention
  1. During normal load and normal engine speed (MIL is blinking)
    - Fuel cut is performed on malfunctioning cylinder
  2. During high load and high engine speed (MIL is blinking)
    - Throttle valve opening angle control is performed
    - All cylinder fuel cut or malfunction cylinder fuel cut
Pass condition detected and then ignition switch turned off
P0327, P0328, P0332 and P0333
Knock Sensor
ECM sets ignition timing to maximum retard.
Ignition switch off
P0351 to P0358
Igniter
ECM cuts fuel.
Pass condition detected
P0504
Stop Light Switch
Accelerator pedal angle is fixed.
Accelerator pedal angle is fixed
P2120, P2121, P2122, P2123, P2125, P2127, P2128 and P2138
Accelerator Pedal Position (APP) Sensor
APP sensor has 2 sensor circuits: Main and Sub.
If either circuit malfunctions, ECM controls engine using other circuit.
If both circuits malfunction, ECM regards accelerator pedal as being released. As a result, throttle valve closed and engine idles.
Pass condition detected and then ignition switch turned off
P2432, P2433, P2437 and P2438
Secondary Air Injection System
Throttle valve opening angle control is performed
Pass condition detected
P2440 and P2442
Secondary Air Injection System
Throttle valve opening angle control is performed
Pass condition detected
P2445 and P2447
Secondary Air Injection System
Throttle valve opening angle control is performed
Pass condition detected

HINT:
  1. *1: The vehicle can be driven slowly when the accelerator pedal is depressed firmly and slowly. If the accelerator pedal is depressed quickly, the vehicle may speed up and slow down erratically.
  2. *2: Misfire related fail-safe operations occur when catalyst overheat malfunctions occur.