DTC P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1) |
DTC P0012 Camshaft Position "A" - Timing Over-Retarded (Bank 1) |
DTC P0021 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 2) |
DTC P0022 Camshaft Position "A" - Timing Over-Retarded (Bank 2) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0011 P0021 | Intake valve timing is not adjusted in valve timing advance range (1 trip detection logic) |
|
| P0012 P0022 | Intake valve timing is not adjusted in valve timing retard range (2 trip detection logic) |
|
| Related DTCs | P0011: Advanced camshaft timing (for Bank 1) P0012: Retarded camshaft timing (for Bank 1) P0021: Advanced camshaft timing (for Bank 2) P0022: Retarded camshaft timing (for Bank 2) |
| Required Sensors/Components (Main) | VVT OCV and VVT Actuator |
| Required Sensors/Components (Related) | Crankshaft position sensor, Camshaft position sensor and Engine coolant temperature sensor |
| Frequency of Operation | Continuous |
| Duration | Within 10 seconds |
| MIL Operation | Advanced camshaft timing: Immediate Retarded camshaft timing: 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not stored | P0010, P0020 (VVT Oil Control Valve) P0016, P0018 (VVT System - Misalignment) P0102, P0103 (Mass Air Flow Sensor) P0115, P0117, P0118 (Engine Coolant Temperature Sensor) P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control) P0335 (Crankshaft Position Sensor) P1340 (Camshaft Position Sensor) |
| Battery voltage | 11 V or more |
| Engine speed | 500 to 4000 rpm |
| ECT | 75 to 100°C (167 to 212°F) |
| Deviation of actual valve timing and target valve timing | More than 5°CA |
| Valve timing | No change at advanced valve timing |
| Deviation of actual valve timing and target valve timing | More than 5°CA |
| Valve timing | No change at retarded valve timing |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| Abnormal bank | Advanced timing over (Valve timing is out of specified range) | Retarded timing over (Valve timing is out of specified range) |
| Bank 1 | P0011 | P0012 |
| Bank 2 | P0021 | P0022 |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011, P0012, P0021 OR P0022) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| P0011, P0012, P0021 or P0022 is output | A |
| P0011, P0012, P0021 or P0022 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE OCV) |
Connect the Techstream to the DLC3.
Start the engine and turn the Techstream on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1) or Control the VVT System (Bank 2).
Check the engine speed while operating the Oil Control Valve (OCV) using the Techstream.
| Operation | Specified Condition |
| OFF | Normal engine speed |
| ON | Soon after OCV switched from OFF to ON, engine idles roughly or stalls |
|
| ||||
| OK | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear DTCs (Click here).
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Read DTCs using the Techstream.
|
| ||||
| OK | ||
| ||
| 4.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TOOTH OF TIMING CHAIN) |

Remove the cylinder head cover LH and RH.
Turn the crankshaft pulley, and align its groove with the timing mark "0" of the timing chain cover.
Check that the timing marks of the camshaft timing gears and camshaft timing exhaust gears are at the positions shown in the illustration.
|
| ||||
| OK | |
| 5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (OCV) |
Inspect the camshaft timing oil control valve assembly (Click here).
|
| ||||
| OK | |
| 6.INSPECT OIL CONTROL VALVE FILTER |
Remove the OCV filter (Click here).
Check that the filter is not clogged.
|
| ||||
| OK | |
| 7.REPLACE CAMSHAFT TIMING GEAR |
Replace the camshaft timing gear (Click here).
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear DTCs (Click here).
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Read the output DTCs using the Techstream.
|
| ||||
| OK | ||
| ||