Home › Engine / Hybrid System · 3UR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0120    Throttle / Pedal Position Sensor / Switch "A" Circuit Malfunction

DTC    P0121    Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem

DTC    P0122    Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input

DTC    P0123    Throttle / Pedal Position Sensor / Switch "A" Circuit High Input

DTC    P0220    Throttle / Pedal Position Sensor / Switch "B" Circuit

DTC    P0222    Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input

DTC    P0223    Throttle / Pedal Position Sensor / Switch "B" Circuit High Input

DTC    P2135    Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation

for Preparation Click here


DESCRIPTION

HINT:
  1. These DTCs relate to the throttle position sensor.

The TP sensor is mounted on the throttle body, and detects the opening angle of the throttle valve. This sensor is a non-contact type. It uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds.
The TP sensor has 2 sensor circuits, each of which transmits a signal, VTA1 and VTA2. VTA1 is used to detect the throttle valve angle and VTA2 is used to detect malfunctions in VTA1. The sensor signal voltages vary between 0 V and 5 V in proportion to the throttle valve opening angle, and are transmitted to the VTA terminals of the ECM.
As the valve closes, the sensor output voltage decreases and as the valve opens, the sensor output voltage increases. The ECM calculates the throttle valve opening angle according to these signals and controls the throttle actuator in response to driver inputs. These signals are also used in calculations such as air-fuel ratio correction, power increase correction and fuel-cut control.

A208679E08


DTC Code
DTC Detection Condition
Trouble Area
P0120
Output voltage of VTA1 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds when accelerator pedal depressed
(1 trip detection logic)
  1. Throttle position sensor (built into throttle body)
  2. ECM
P0121
The difference between the VTA1 and VTA2 voltages is below 0.8 V or higher than 1.6 V for 2 seconds
(1 trip detection logic)
  1. Throttle position sensor (built into throttle body)
  2. Throttle position sensor circuit
  3. ECM
P0122
Output voltage of VTA1 0.2 V or less for 2 seconds when accelerator pedal depressed
(1 trip detection logic)
  1. Throttle position sensor (built into throttle body)
  2. Short in VTA1 circuit
  3. Open in VC circuit
  4. ECM
P0123
Output voltage of VTA1 4.535 V or more for 2 seconds when accelerator pedal depressed
(1 trip detection logic)
  1. Throttle position sensor (built into throttle body)
  2. Open in VTA1 circuit
  3. Open in E2 circuit
  4. Short between VC and VTA1 circuits
  5. ECM
P0220
Output voltage of VTA2 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds when accelerator pedal depressed
(1 trip detection logic)
  1. Throttle position sensor (built into throttle body)
  2. ECM
P0222
Output voltage of VTA2 1.75 V or less for 2 seconds when accelerator pedal depressed
(1 trip detection logic)
  1. Throttle position sensor (built into throttle body)
  2. Short in VTA2 circuit
  3. Open in VC circuit
  4. ECM
P0223
Output voltage of VTA2 4.8 V or more, and VTA1 between 0.2 V and 2.02 V for 2 seconds when accelerator pedal depressed
(1 trip detection logic)
  1. Throttle position sensor (built into throttle body)
  2. Open in VTA2 circuit
  3. Open in E2 circuit
  4. Short between VC and VTA2 circuits
  5. ECM
P2135
Either condition (a) or (b) met (1 trip detection logic):
(a) Difference between output voltages of VTA1 and VTA2 0.02 V or less for 0.5 seconds or more
(b) Output voltage of VTA1 0.2 V or less, and VTA2 1.75 V or less, for 0.4 seconds or more
  1. Short between VTA1 and VTA2 circuits
  2. Throttle position sensor (built into throttle body)
  3. ECM

HINT:
  1. When any of these DTCs are set, check the throttle valve opening angle by entering the following menus: Powertrain / Engine and ECT / Data List / ETCS / Throttle Position No. 1 and Throttle Position No. 2.
  1. Throttle Position No. 1 is the VTA1 signal, and Throttle Position No. 2 is the VTA2 signal.

    Reference (Normal Condition):

    Display Item
    Accelerator Pedal Fully Released
    Accelerator Pedal Fully Depressed
    Throttle Position No. 1
    0.5 to 1.1 V
    3.2 to 4.8 V
    Throttle Position No. 2
    2.1 to 3.1 V
    4.6 to 5.0 V


MONITOR DESCRIPTION

P0120, P0122, P0123, P0220, P0222, P0223, P2135
The ECM uses the throttle position sensor to monitor the throttle valve opening angle. There are several checks that the ECM performs to confirm the proper operation of the throttle position sensor.
  1. A specific voltage difference is expected between the sensor terminals, VTA1 and VTA2, for each throttle valve opening angle. If the difference between VTA1 and VTA2 is incorrect, the ECM interprets this as a malfunction in the sensor, and stores a DTC.
  1. VTA1 and VTA2 each have a specific voltage range. If VTA1 or VTA2 is outside the normal operating range, the ECM interprets this as a malfunction in the sensor, and stores a DTC.
  1. VTA1 and VTA2 should never be close to the same voltage level. If VTA1 is within 0.02 V of VTA2, the ECM determines that there is a short circuit in the sensor, and stores a DTC.
If the malfunction is not repaired successfully, a DTC is stored 10 seconds after the engine is next started.
P0121
This sensor transmits 2 signals: VTA1 and VTA2. VTA1 is used to detect the throttle opening angle and VTA2 is used to detect malfunctions in VTA1. The ECM performs several checks to confirm the proper operation of the throttle position sensor and VTA1.
For each throttle opening angle, a specific voltage difference is expected between the outputs of VTA1 and VTA2. If the output voltage difference between the two signals deviates from the normal operating range, the ECM interprets this as a malfunction of the TP sensor. The ECM illuminates the MIL and stores the DTC.
If the malfunction is not repaired successfully, the DTC is stored 2 seconds after the engine is next started.

MONITOR STRATEGY


Related DTCs
P0120: Throttle position sensor 1 range check (Fluctuating)
P0121: Throttle position sensor rationality
P0122: Throttle position sensor 1 range check (Low voltage)
P0123: Throttle position sensor 1 range check (High voltage)
P0220: Throttle position sensor 2 range check (Fluctuating)
P0222: Throttle position sensor 2 range check (Low voltage)
P0223: Throttle position sensor 2 range check (High voltage)
P2135: Throttle position sensor range check (Correlation)
Required Sensors/Components (Main)
Throttle position sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
2 seconds: P0120, P0122, P0123, P0220, P0222 and P0223
Within 2 seconds: P0121
0.5 seconds: P2135 Case 1
0.4 seconds: P2135 Case 2
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


P0120, P0122, P0123, P0220, P0222, P0223, P02135 
Monitor runs whenever following DTCs not present
None
Either of following conditions A or B met
-
A. Ignition switch ON
0.012 seconds or more
B. Electronic throttle actuator power
ON

P0121 
Monitor runs whenever following DTCs not present
P0120, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
Either of following conditions met
-
A. Ignition switch ON
0.012 seconds or more
B. Electronic throttle actuator power
ON

TYPICAL MALFUNCTION THRESHOLDS


P0120: 
VTA1 voltage
0.2 V or less, or 4.54 V or more

P0121: 
VTA1 voltage
-
Difference of TP sensor voltage between VTA and VTA2 x 0.8
Higher than 1.6 V
Difference of TP sensor voltage between VTA and VTA2 x 0.8
Below 0.8 V

P0122: 
VTA1 voltage
0.2 V or less

P0123: 
VTA1 voltage
4.54 V or more

P0220: 
Either of following conditions A or B met
-
A. VTA2 voltage
1.75 V or less
B. All of following conditions are met
-
VTA2 voltage
4.8 V or more
VTA1 voltage
0.2 V or more, and 2.02 V or less

P0222: 
VTA2 voltage
1.75 V or less

P0223: 
All of the following conditions are met
-
VTA2 voltage
4.8 V or more
VTA1 voltage
0.2 V or more, and 2.02 V or less

P2135 Case 1: 
Difference between VTA1 and VTA2 voltages
0.02 V or less

P2135 Case 2: 
All of the following conditions are met
-
VTA1 voltage
0.2 V or less
VTA2 voltage
1.75 V or less

COMPONENT OPERATING RANGE


VTA1 voltage
0.2 to 4.535 V
VTA2 voltage
1.75 to 4.8 V
Difference between VTA1 and VTA2 voltages
0.02 V or more

CONFIRMATION DRIVING PATTERN


A198824E01

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine.
  7. With the vehicle stationary, fully depress and release the accelerator pedal [B].
  8. Idle the engine for 2 seconds or more [C].
  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
  10. Read the Pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0120, P0121, P0122, P0123, P0220, P0222, P0223 or P2135.
  13. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows ABNORMAL, the system has a malfunction.
    2. If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [D] again.

  14. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


FAIL-SAFE

When any of these DTCs, as well as other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are set, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 7° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM


A178644E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING TECHSTREAM (THROTTLE POSITION)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / ETCS / Throttle Position No. 1 and Throttle Position No. 2.

  1. Read the values displayed on the Techstream.

    Result 
    When Accelerator Pedal Released
    When Accelerator Pedal Depressed
    Trouble Area
    Proceed to
    Throttle Position No. 1
    Throttle Position No. 2
    Throttle Position No. 1
    Throttle Position No. 2
    0 to 0.2 V
    0 to 0.2 V
    0 to 0.2 V
    0 to 0.2 V
    VC circuit open
    A
    4.5 to 5.0 V
    4.5 to 5.0 V
    4.5 to 5.0 V
    4.5 to 5.0 V
    E2 circuit open
    0 to 0.2 V,
    or 4.5 to 5.0 V
    2.1 V to 3.1 V
    (Fail-safe)
    0 to 0.2 V,
    or 4.5 to 5.0 V
    2.1 V to 3.1 V
    (Fail-safe)
    VTA1 circuit open or ground short
    0.6 V to 1.4 V
    (Fail-safe)
    0 to 0.2 V,
    or 4.5 to 5.0 V
    0.6 V to 1.4 V
    (Fail-safe)
    0 to 0.2 V,
    or 4.5 to 5.0 V
    VTA2 circuit open or ground short
    0.5 to 1.1 V
    2.1 to 3.1 V
    3.2 to 4.8 V
    (Not fail-safe)
    4.6 to 5.0 V
    (Not fail-safe)
    Throttle position sensor circuit normal
    B

    HINT:
    1. DTC P0121 is stored when the voltages output from VTA1 and VTA2 are not consistent with the characteristics of the sensors. Therefore, check the Freeze Frame Data when this DTC is output. Use the following formula to confirm relative fluctuations in voltage.

      Features of sensor output:
      VTA2 x 0.8 is approximately equal to VTA1 + 1.11 V
      VTA1: Throttle Position No. 1
      VTA2: Throttle position No. 2

    2. If DTC P0121 is output, proceed to "CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)".



B
Go to step 5
A


2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
A164721E05
  1. Disconnect the D4 throttle body connector.

  1. Disconnect the D56 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D4-5 (VC) - D56-80 (VCTA)
    Always
    Below 1 Ω
    D4-6 (VTA) - D56-78 (VTA1)
    Always
    Below 1 Ω
    D4-4 (VTA2) - D56-77 (VTA2)
    Always
    Below 1 Ω
    D4-3 (E2) - D56-79 (ETA)
    Always
    Below 1 Ω
    D4-5 (VC) or D56-80 (VCTA) - Body ground
    Always
    10 kΩ or higher
    D4-6 (VTA) or D56-78 (VTA1) - Body ground
    Always
    10 kΩ or higher
    D4-4 (VTA2) or D56-77 (VTA2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT ECM (VC VOLTAGE)
A107895E41
  1. Disconnect the D4 throttle body connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D4-5 (VC) - D4-3 (E2)
    Ignition switch ON
    4.5 to 5.5 V



NG
REPLACE ECM (Click here)
OK


4.REPLACE THROTTLE BODY ASSEMBLY
  1. Replace the throttle body assembly (Click here).


NEXT


5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 15 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P0120, P0121, P0122, P0123, P0220, P0222, P0223 and/or P2135 are output
    A
    No DTC is output
    B



B
END
A

REPLACE ECM (Click here)