DTC P0037 Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2) |
DTC P0038 Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2) |
DTC P0057 Oxygen Sensor Heater Control Circuit Low (Bank 2 Sensor 2) |
DTC P0058 Oxygen Sensor Heater Control Circuit High (Bank 2 Sensor 2) |
DTC P0141 Oxygen Sensor Heater Circuit Malfunction (Bank 1 Sensor 2) |
DTC P0161 Oxygen Sensor Heater Circuit Malfunction (Bank 2 Sensor 2) |
DTC P102D O2 Sensor Heater Circuit Performance Bank 1 Sensor 2 Stuck ON |
DTC P105D O2 Sensor Heater Circuit Performance Bank 2 Sensor 2 Stuck ON |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0037 P0057 | The heater current is less than the specified value while the heater is operating. (1 trip detection logic) |
|
| P0038 P0058 | The heater current is higher than the specified value while the heater is operating. (1 trip detection logic) |
|
| P0141 P0161 | The cumulative heater resistance correction value exceeds the threshold. (2 trip detection logic) |
|
| P102D P105D | The heater current is higher than the specified value while the heater is not operating. (1 trip detection logic) | ECM |
| Related DTCs | P0037: Heated oxygen sensor heater (for Bank 1) range check (Low electrical current) P0038: Heated oxygen sensor heater (for Bank 1) range check (High electrical current) P0057: Heated oxygen sensor heater (for Bank 2) range check (Low electrical current) P0058: Heated oxygen sensor heater (for Bank 2) range check (High electrical current) P0141: Heated oxygen sensor heater performance (for Bank 1) P0161: Heated oxygen sensor heater performance (for Bank 2) P102D: Heated oxygen sensor heater stuck ON (for Bank 1 Sensor 2) P105D: Heated oxygen sensor heater stuck ON (for Bank 2 Sensor 2) |
| Required Sensors/Components (Main) | Heated oxygen sensor heater |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous: P0037, P0038, P0057, P0058 P102D and P105D Once per driving cycle: P0141 and P0161 |
| Duration | 0.5 seconds: P0037, P0057, P102D and P105D Within 3 seconds: P0038 and P0058 10 seconds: P0141 and P0161 0.5 seconds: |
| MIL Operation | Immediate: P0037, P0038, P0057, P0058, P102D and P105D 2 driving cycles: P0141 and P0161 |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not stored | P0032, P0052 (Air fuel ratio sensor heater) P0038, P0058 (Rear oxygen sensor heater) |
| Battery voltage | 10.5 V or higher |
| Engine | Running |
| Starter | OFF |
| Catalyst active A/F control | Not operating |
| Time after heater ON | 10 seconds or more |
| Learned heater OFF current operation | Complete |
| Heater OFF current learned value | Acquired |
| Monitor runs whenever following DTCs not stored | P0031, P0032, P0051, P0052 (Air fuel ratio sensor heater) P0038, P0058 (Rear oxygen sensor heater) |
| Battery voltage | 10.5 V or higher |
| Engine | Running |
| Starter | OFF |
| Catalyst active A/F control | Not operating |
| Time after heater ON | 10 seconds or more |
| Learned heater OFF current operation | Complete |
| Heated oxygen sensor heater OFF current | Higher than 3.5 A |
| Hybrid IC high current limiter port | Fail |
| Monitor runs whenever following DTCs not stored | None |
| Battery voltage | 10.5 V or higher |
| Engine | Running |
| Starter | OFF |
| Catalyst active A/F control | Not operating |
| Time after heater ON | 10 seconds or more |
| Learned heater OFF current operation | Complete |
| Monitor runs whenever following DTCs not stored | P0031, P0032, P0051, P0052 (Air fuel ratio sensor heater) P0037, P0038, P0057, P0058 (Rear oxygen sensor heater) P101D, P102D, P103D, P105D (Air fuel ratio sensor heater) |
| Battery voltage | 10.5 V or higher |
| Fuel cut | OFF |
| Time after fuel cut ON to OFF | 30 seconds or more |
| Accumulated heater ON time | 100 seconds or more |
| Learned heater OFF current operation | Complete |
| Monitor runs whenever following DTCs not stored | None |
| Duration that rear heated oxygen sensor impedance is less than 15 kΩ | 2 seconds or more |
| Monitor runs whenever following DTCs not stored | P0031, P0032, P0051, P0052 (Air fuel ratio sensor heater) P0037, P0038, P0057, P0058 (Rear oxygen sensor heater) |
| Battery voltage | 10.5 V or higher |
| Engine | Running |
| Starter | OFF |
| Catalyst active A/F control | Not operating |
| Time after heater ON | 10 seconds or more |
| Learned heater OFF current operation | Complete |
| Hybrid IC high current limiter port | Fail |
| Heater current - Learned heater OFF current | 0.3 A or less |
| Heated oxygen sensor heater ON current | 0.3 A or less |
| Hybrid IC high current limiter port | Fail |
| Heated oxygen sensor heater output | ON |
| Accumulated heater resistance | Varies with sensor element temperature (Example: Higher than 23 Ω) |
| Heated oxygen sensor heater ON current | Higher than 1 A |
| Heated Oxygen (HO2) sensor heater current | 0.4 to 1 A (when engine idles, HO2 sensor warmed up and battery voltage 11 to 14 V) |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the D17 or D18 HO2 sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (HT1B) - 2 (+B) | 20°C (68°F) | 11 to 16 Ω |
| 1 (HT1B) - 4 (E1) | Always | 10 kΩ or higher |
| 1 (HT2B) - 2 (+B) | 20°C (68°F) | 11 to 16 Ω |
| 1 (HT2B) - 4 (E1) | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 2.CHECK TERMINAL VOLTAGE (+B OF HO2 SENSOR) |
![]() |
Disconnect the D17 or D18 HO2 sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D17-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| D18-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 3.INSPECT INTEGRATION RELAY (EFI MAIN) |
![]() |
Remove the integration relay from the engine room relay block .
Inspect the EFI NO. 1 fuse.
Remove the EFI NO. 1 fuse from the integration relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| EFI NO. 1 fuse | Always | Below 1 Ω |
Reinstall the EFI NO. 1 fuse.
Inspect the EFI MAIN relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1C-1 - 1B-4 | When no battery voltage applied to terminals 1B-2 and 1B-3 | 10 kΩ or higher |
| When battery voltage applied to terminals 1B-2 and 1B-3 | Below 1 Ω |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (HO2 SENSOR - INTEGRATION RELAY) |
![]() |
Check the EFI NO. 2 fuse.
Remove the EFI NO. 2 fuse from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| EFI NO. 2 fuse | Always | Below 1 Ω |
Reinstall the EFI NO. 2 fuse.
Disconnect the D17 or D18 HO2 sensor connector.
Remove the integration relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D17-2 (+B) - 1B-4 | Always | Below 1 Ω |
| D18-2 (+B) - 1B-4 | Always | Below 1 Ω |
| D17-2 (+B) or 1B-4 - Body ground | Always | 10 kΩ or higher |
| D18-2 (+B) or 1B-4 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (HO2 SENSOR - ECM) |
![]() |
Disconnect the D17 or D18 HO2 sensor connector.
Disconnect the D56 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D17-1 (HT1B) - D56-45 (HT1B) | Always | Below 1 Ω |
| D18-1 (HT2B) - D56-44 (HT2B) | Always | Below 1 Ω |
| D17-1 (HT1B) or D56-45 (HT1B) - Body ground | Always | 10 kΩ or higher |
| D18-1 (HT2B) or D56-44 (HT2B) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.CHECK WHETHER DTC OUTPUT RECURS |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (Click here).
Start the engine.
Allow the engine to idle for 2 minutes or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| No DTC is output | A |
| P0037, P0038, P0057, P0058, P0141, P0161, P102D and/or P105D are output | B |
|
| ||||
| A | ||
| ||