Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM

WIPER AND WASHER SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the Techstream or to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the Techstream on.

  4. Enter the following menus: Body Electrical / (desired system) / Data List.

  5. According to the display on the Techstream, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Rear Wiper HI SW Signal
    Rear wiper HI switch / ON or OFF
    ON: Rear wiper switch in HI position
    OFF: Rear Wiper switch not in HI position
    -
    Rear Wiper LO SW Signal
    Rear wiper LO switch / ON or OFF
    ON: Rear wiper switch in LO position
    OFF: Rear Wiper switch not in LO position
    -
    Rear Washer SW Signal
    Rear washer switch / ON or OFF
    ON: Rear washer switch on
    OFF: Rear washer switch off
    -

    Back Door P/W 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Wiper Retracted Position
    Rear wiper retracting switch signal / ON or OFF
    ON: Rear wiper in retracting position
    OFF: Rear wiper in other position
    -
    Wiper Reverse Position
    Rear wiper reverse position switch signal / ON or OFF
    ON: Rear wiper in reverse position
    OFF: Rear wiper in other position
    -
    Linked Rear Wiper Washer
    Washer linkage function / AVAIL or NOT AVL
    Customized value can be displayed
    This item is only used to display the customize status.
    Rewipe Function
    Washer drip preventive function / AVAIL or NOT AVL
    Customized value can be displayed
    This item is only used to display the customize status.
    Back Door P/W Status
    Back door power window position /Open or Close
    Open: Back door window is open
    Close: Back door window is closed
    -

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Washer Switch
    Washer fluid level warning switch / ON or OFF
    ON: Washer jar and tank is empty
    OFF: Washer jar and tank is full
    -


PERFORM ACTIVE TEST

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the Techstream or to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the Techstream on.

  4. Enter the following menus: Body Electrical / (desired system) / Active Test.

  5. According to the display on the Techstream, perform the Active Test.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Rear Wiper Washer Motor Relay
    Rear Wiper Washer motor operation
    ON/OFF
    -

    Back Door P/W 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Rear Wiper Active
    Rear Wiper motor operation
    STOP/ACTIVE
    -