Home › Engine / Hybrid System · 3UR-FBE › ENGINE CONTROL › SFI SYSTEM

DTC    P0327    Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)

DTC    P0328    Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)

DTC    P032C    Knock Sensor 3 Circuit Low

DTC    P032D    Knock Sensor 3 Circuit High

DTC    P0332    Knock Sensor 2 Circuit Low Input (Bank 2)

DTC    P0333    Knock Sensor 2 Circuit High Input (Bank 2)

DTC    P033C    Knock Sensor 4 Circuit Low Input

DTC    P033D    Knock Sensor 4 Circuit High Input

for Preparation Click here


DESCRIPTION

A flat type knock sensor (non-resonant type) has a structure that can detect vibrations between approximately 6 kHz and 15 kHz.
Knock sensors are fitted onto the engine block to detect engine knocking.
The knock sensor contains a piezoelectric element which generates a voltage when it becomes deformed.
The voltage is generated when the engine block vibrates due to knocking. Any occurrence of engine knocking can be suppressed by delaying the ignition timing.

DTC No.
DTC Detection Condition
Trouble Area
P0327
Output voltage of knock sensor (for Bank 1 Sensor 1) is 0.5 V or less
(1 trip detection logic)
  1. Short in knock sensor (for Bank 1 Sensor 1) circuit
  1. Knock sensor (for Bank 1 Sensor 1)
  1. ECM
P0328
Output voltage of knock sensor (for Bank 1 Sensor 1) is 4.5 V or more
(1 trip detection logic)
  1. Open in knock sensor (for Bank 1 Sensor 1) circuit
  1. Knock sensor (for Bank 1 Sensor 1)
  1. ECM
P0332
Output voltage of knock sensor (for Bank 2 Sensor 1) is 0.5 V or less
(1 trip detection logic)
  1. Short in knock sensor (for Bank 2 Sensor 1) circuit
  1. Knock sensor (for Bank 2 Sensor 1)
  1. ECM
P0333
Output voltage of knock sensor (for Bank 2 Sensor 1) is 4.5 V or more
(1 trip detection logic)
  1. Open in knock sensor (for Bank 2 Sensor 1) circuit
  1. Knock sensor (for Bank 2 Sensor 1)
  1. ECM
P032C
Output voltage of knock sensor (for Bank 1 Sensor 2) is 0.5 V or less
(1 trip detection logic)
  1. Short in knock sensor (for Bank 1 Sensor 2) circuit
  1. Knock sensor (for Bank 1 Sensor 2)
  1. ECM
P032D
Output voltage of knock sensor (for Bank 1 Sensor 2) is 4.5 V or more
(1 trip detection logic)
  1. Open in knock sensor (for Bank 1 Sensor 2) circuit
  1. Knock sensor (for Bank 1 Sensor 2)
  1. ECM
P033C
Output voltage of knock sensor (for Bank 2 Sensor 2) is 0.5 V or less
(1 trip detection logic)
  1. Short in knock sensor (for Bank 2 Sensor 2) circuit
  1. Knock sensor (for Bank 2 Sensor 2)
  1. ECM
P033D
Output voltage of knock sensor (for Bank 2 Sensor 2) is 4.5 V or more
(1 trip detection logic)
  1. Open in knock sensor (for Bank 2 Sensor 2) circuit
  1. Knock sensor (for Bank 2 Sensor 2)
  1. ECM

HINT:
When DTC P0327, P0328, P0332, P0333, P032C, P032D, P033C or P033D is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. Fail-safe mode continues until the ignition switch is turned off.

Reference: Inspection using an oscilloscope
A150243E01

Standard:

Tester Connection
Tool Setting
Condition
Specified Condition
D56-94 (KNK1) - D56-93 (EKNK)
0.01 to 10 V/DIV.
0.01 to 10 msec./DIV.
Keep engine speed at 4000 rpm with warm engine
The correct waveform is as shown
D56-117 (KNK2) - D56-116 (EKN2)
0.01 to 10 V/DIV.
0.01 to 10 msec./DIV.
Keep engine speed at 4000 rpm with warm engine
The correct waveform is as shown
D56-96 (KNK3) - D56-95 (EKN3)
0.01 to 10 V/DIV.
0.01 to 10 msec./DIV.
Keep engine speed at 4000 rpm with warm engine
The correct waveform is as shown
D56-119 (KNK4) - D56-118 (EKN4)
0.01 to 10 V/DIV.
0.01 to 10 msec./DIV.
Keep engine speed at 4000 rpm with warm engine
The correct waveform is as shown


MONITOR DESCRIPTION

The knock sensor, located on the cylinder block, detects spark knock. When spark knock occurs, the piezoelectric element of the sensor vibrates. When the ECM detects a voltage in this frequency range, it retards the ignition timing to suppress the spark knock.
The ECM also senses background engine noise with the knock sensor and uses this noise to check for faults in the sensor. If the knock sensor output voltage is outside the normal range, the ECM interprets this as a fault in the knock sensor and stores a DTC.

MONITOR STRATEGY


Related DTCs
P0327: Knock sensor (for Bank 1 Sensor 1) open/short (Low voltage)
P0328: Knock sensor (for Bank 1 Sensor 1) open/short (High voltage)
P0332: Knock sensor (for Bank 2 Sensor 1) open/short (Low voltage)
P0333: Knock sensor (for Bank 2 Sensor 1) open/short (High voltage)
P032C: Knock sensor (for Bank 1 Sensor 2) open/short (Low voltage)
P032D: Knock sensor (for Bank 1 Sensor 2) open/short (High voltage)
P033C: Knock sensor (for Bank 2 Sensor 2) open/short (Low voltage)
P033D: Knock sensor (for Bank 2 Sensor 2) open/short (High voltage)
Required Sensors/Components (Main)
Knock sensor (Bank 1, 2 Sensor 1, 2)
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
1 second
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs are not stored
None
Battery voltage
10.5 V or more
Time after engine start
5 seconds or more

TYPICAL MALFUNCTION THRESHOLDS


Knock Sensor Range Check (Low voltage): P0327, P0332, P032C and P033C: 
Knock sensor voltage
Less than 0.5 V

Knock Sensor Range Check (High voltage): P0328, P0333, P032D and P033D: 
Knock sensor voltage
More than 4.5 V

CONFIRMATION DRIVING PATTERN


A199234E01

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and wait 10 seconds.
  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
  8. Read the pending DTC.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Input the DTC: P0327, P0328, P032C, P032D, P0332, P0333, P033C or P033D.
  11. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    If the judgment result shows INCOMPLETE or N/A, idle the engine for 5 minutes and check the DTC judgment result again [C].

  12. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A179937E01


INSPECTION PROCEDURE

HINT:
  1. DTCs P0327 and P0328 are for the bank 1 sensor 1 knock sensor circuit.
  2. DTCs P032C and P032D are for the bank 1 sensor 2 knock sensor circuit.
  3. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  4. DTCs P0332 and P0333 are for the bank 2 sensor 1 knock sensor circuit.
  5. DTCs P033C and P033D are for the bank 2 sensor 2 knock sensor circuit.
  6. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  7. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.INSPECT KNOCK SENSOR
A136305E60
  1. Disconnect the D56 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D56-94 (KNK1) - D56-93 (EKNK)
    20°C (68°F)
    120 to 280 kΩ
    D56-117 (KNK2) - D56-116 (EKN2)
    20°C (68°F)
    120 to 280 kΩ
    D56-96 (KNK3) - D56-95 (EKN3)
    20°C (68°F)
    120 to 280 kΩ
    D56-119 (KNK4) - D56-118 (EKN4)
    20°C (68°F)
    120 to 280 kΩ

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 3
A


2.CHECK HARNESS AND CONNECTOR (ECM - KNOCK SENSOR)
A148717E17
  1. Disconnect the D56 ECM connector.

  1. Disconnect the b3, b4, b1 or b2 knock sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    b1-2 - D56-94 (KNK1)
    Always
    Below 1 Ω
    b1-1 - D56-93 (EKNK)
    Always
    Below 1 Ω
    b2-2 - D56-117 (KNK2)
    Always
    Below 1 Ω
    b2-1 - D56-116 (EKN2)
    Always
    Below 1 Ω
    b3-2 - D56-96 (KNK3)
    Always
    Below 1 Ω
    b3-1 - D56-95 (EKN3)
    Always
    Below 1 Ω
    b4-2 - D56-119 (KNK4)
    Always
    Below 1 Ω
    b4-1 - D56-118 (EKN4)
    Always
    Below 1 Ω
    b1-2 or D56-94 (KNK1) - Body ground
    Always
    10 kΩ or higher
    b1-1 or D56-93 (EKNK) - Body ground
    Always
    10 kΩ or higher
    b2-2 or D56-117 (KNK2) - Body ground
    Always
    10 kΩ or higher
    b2-1 or D56-116 (EKN2) - Body ground
    Always
    10 kΩ or higher
    b3-2 or D56-96 (KNK3) - Body ground
    Always
    10 kΩ or higher
    b3-1 or D56-95 (EKN3) - Body ground
    Always
    10 kΩ or higher
    b4-2 or D56-119 (KNK4) - Body ground
    Always
    10 kΩ or higher
    b4-1 or D56-118 (EKN4) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE KNOCK SENSOR (Click here)  

3.INSPECT ECM
  1. Disconnect the b3, b4, b1 or b2 knock sensor connector.



    A148715E18
  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Ignition switch ON
    4.5 to 5.5 V



NG
REPLACE ECM (Click here)
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)