Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM

POWER DOOR LOCK CONTROL SYSTEM > All Doors cannot be Locked / Unlocked Simultaneously

for Preparation Click here


DESCRIPTION

The main body ECU receives switch signals from the power window regulator master switch, switch signal from the front door lock switch, tail gate control switch signal and driver side door key cylinder switch signals from the front door look. The main body ECU activates the door look motor on each door according to the signals.

HINT:
Since the power door lock control system has functions that use LIN communication, first confirm that there is no malfunction in the communication system by inspecting the LIN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.


WIRING DIAGRAM


B189773E03


INSPECTION PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION
  1. Check the power door lock operation.

    Result 
    Result
    Proceed to
    All doors cannot be locked through power window regulator master switch, door control switch RH, tail gate control switch, and driver side door key link switch.
    A
    All doors cannot be locked through power window regulator master switch .
    B
    All doors cannot be locked through tail gate control switch.
    C
    All doors cannot be locked through door control switch RH.
    D
    All doors cannot be locked through driver side door key link switch.
    E



B
Go to step 4

C
Go to step 5

D
Go to step 9

E
Go to step 12
A


2.INSPECT FUSES (ECU-B1, DR/LCK)
E160630E12
  1. Remove the ECU-B1 and DR/LCK fuses.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    ECU-B1 fuse
    Always
    Below 1 Ω
    DR/LCK fuse
    Always
    Below 1 Ω

  1. Reinstall the ECU-B1 and DR/LCK fuses.



NG
CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSES
OK


3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)
B189796E02
  1. Disconnect DA, DB, and DD main body ECU connector.

  1. Measure the voltage and resistance and voltage according to the value(s) in the table below.

    Standard Voltage :
    Tester Connection
    Condition
    Specified Condition
    DA-1 (ALTB) - Body ground
    Always
    11 to 14 V
    DB-13 (BECU) - Body ground
    Always
    11 to 14 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    DD-62 (GND1) - Body ground
    Always
    Below 1 Ω

  1. Reconnect main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

4.READ VALUE USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Master Switch / Data List.

  1. According to the display on the Techstream, read the "Data List".

    Master Switch 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Door Lock Switch Status
    Driver door lock switch signal/ ON or OFF
    ON: Driver door lock switch is turned to LOCK
    OFF: ON: Driver door lock switch is not turned
    -
    Door Unlock Switch Status
    Driver door unlock switch signal/ ON or OFF
    ON: Driver door unlock switch is turned to UNLOCK
    OFF: ON: Driver door unlock switch is not turned
    -

    OK:
    The display is as specified in the normal condition column.



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH (Click here)
OK

REPLACE MAIN BODY ECU 

5.READ VALUE USING TECHSTREAM (TAIL GATE CONTROL SWITCH OPERATION)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Back Door P/W / Data List.

  1. According to the display on the Techstream, read the "Data List".

    Back Door P/W (Back Door ECU) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Key Switch Operation Locked
    Tail gate control switch signal/ON or OFF
    ON: Back door key cylinder is turned to LOCK
    OFF: Driver side door key cylinder is not turned
    -
    Key Switch Operation Unlocked
    Tail gate control switch signal/ON or OFF
    ON: Back door key cylinder is turned to UNLOCK
    OFF: Back door key cylinder is not turned
    -

    OK:
    The display is as specified in the normal condition column.



NG
Go to step 7
OK


6.READ VALUE USING TECHSTREAM (BACK DOOR OPEN)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. According to the display on the Techstream, read the "Data List".

    Main Body (Main Body ECU) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Back Door Open
    Back door lock signal/Permit or Prohibit
    Permit: Back door is UNLOCK
    Prohibit: Back door is LOCK
    -

    OK:
    The display is as specified in the normal condition column.



NG
REPLACE BACK DOOR ECU (Click here)
OK

REPLACE MAIN BODY ECU 

7.CHECK HARNESS AND CONNECTOR (TAIL GATE CONTROL SWITCH - BACK DOOR ECU)
B189797E01
  1. Disconnect V18 switch connector.

  1. Disconnect V3 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    V18-1 (UL) - V3-7 (BKUL)
    Always
    Below 1 Ω
    V18-2 (L) - V3-8 (BKL)
    Always
    Below 1 Ω
    V18-3 (E) - V3-19 (KEYE)
    Always
    Below 1 Ω
    V18-1 (UL) or V3-7 (BKUL) - Body ground
    Always
    10 kΩ or higher
    V18-2 (L) or V3-8 (BKL) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the switch and ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT TAIL GATE CONTROL SWITCH
B189798E01
  1. Remove the tail gate control switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (UL) - 3 (E)
    Lock position
    Below 1 Ω
    2 (L) - 3 (E)
    Unlock position
    Below 1 Ω
    2 (L) - 3 (E)
    Lock position
    10 kΩ or higher
    1 (UL) - 3 (E)
    Unlock position
    10 kΩ or higher

  1. Reinstall the tail gate control switch.



NG
REPLACE TAIL GATE CONTROL SWITCH (Click here)
OK

REPLACE BACK DOOR ECU (Click here)  

9.READ VALUE USING TECHSTREAM (DOOR LOCK SWITCH RH)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. According to the display on the Techstream, read the "Data List".

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Door Lock SW-Lock
    Door manual lock switch signal ON or OFF
    ON: Door control switch is pushed to lock position
    OFF: Door control switch is not pushed
    -
    Door Lock SW-Unlock
    Door manual unlock switch signal / ON or OFF
    ON: Door control switch is pushed to unlock position
    OFF: Door control switch is not pushed
    -

    OK:
    The display is as specified in the normal condition column.



NG
Go to step 10
OK

REPLACE MAIN BODY ECU 

10.CHECK HARNESS AND CONNECTOR (FRONT DOOR CONTROL SWITCH - MAIN BODY ECU)
  1. Disconnect the L5 switch connector.


E147842E02

  1. Disconnect the DD ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L5-4 (L) - DD-49 (L1)
    Always
    Below 1 Ω
    L5-2 (UL) - DD-40 (UL1)
    Always
    Below 1 Ω
    L5-3 (E) - Body ground
    Always
    Below 1 Ω
    DD-49 (L1) - Body ground
    Always
    10 kΩ or higher
    DD-40 (UL1) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the switch and ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.INSPECT DOOR CONTROL SWITCH RH
E146781E04
  1. Remove the door control switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    4 (L) - 3 (E)
    Lock
    Below 1 Ω
    4 (L) - 3 (E)
    OFF (Free)
    10 kΩ or higher
    2 (UL) - 3 (E)
    OFF (Free)
    10 kΩ or higher
    2 (UL) - 3 (E)
    Unlock
    Below 1 Ω

  1. Reinstall the door control switch.



NG
REPLACE DOOR CONTROL SWITCH (Click here)
OK

REPLACE MAIN BODY ECU 

12.READ VALUE USING TECHSTREAM (DRIVER SIDE LOCK/UNLOCK KEY SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. According to the display on the Techstream, read the "Data List".

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Door Key SW-Lock
    Driver door lock/unlock switch lock signal (Key-linked lock switch) / ON or OFF
    ON: Driver side door key cylinder is turned to lock position
    OFF: Driver side door key cylinder is not turned
    -
    D Door Key SW-UL
    Driver door lock/unlock switch unlock signal (2 step key-linked unlock switch) / ON or OFF
    ON: Driver side door key cylinder is turned to unlock position
    OFF: Driver side door key cylinder is not turned
    -

OK:
The display is as specified in the normal condition column.



NG
Go to step 13
OK

REPLACE MAIN BODY ECU 

13.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK LH - MAIN BODY ECU)
  1. Disconnect the DD and H4 ECU connector.

  1. Disconnect the M4 door lock connector.


C211923E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M4-9 (L) - DD-53 (L2)
    Always
    Below 1 Ω
    M4-10 (UL) - H4-10 (UL3)
    Always
    Below 1 Ω
    M4-7 (E) - Body ground
    Always
    Below 1 Ω
    M4-10 (UL) - Body ground
    Always
    10 kΩ or higher
    M4-9 (L) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECU and door lock connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14.INSPECT FRONT DOOR LOCK LH (DOOR KEY LOCK AND UNLOCK SWITCH)
E146713E05
  1. Remove the door key lock and unlock switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    7 (E) - 9 (L)
    ON (Door lock set to LOCK)
    Below 1 Ω
    7 (E) - 9 (L)
    7 (E) - 10 (UL)
    OFF (Free)
    10 kΩ or higher
    7 (E) - 10 (UL)
    ON (Door lock set to UNLOCK)
    Below 1 Ω

  1. Reinstall the front door lock LH.



NG
REPLACE FRONT DOOR LOCK LH (DOOR KEY LOCK AND UNLOCK SWITCH) (Click here)
OK

REPLACE MAIN BODY ECU