Home › Engine / Hybrid System · CRUISE CONTROL › DYNAMIC LASER CRUISE CONTROL SYSTEM

DYNAMIC LASER CRUISE CONTROL SYSTEM > Cruise Control Switch Circuit

for Preparation Click here


DESCRIPTION

The cruise control main switch operates 8 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP, CANCEL, and MODE. The SET, TAP-DOWN, and - (COAST) functions, and the RES (RESUME), TAP-UP, and + (ACCEL) functions are operated with the same switch. The cruise control main switch is an automatic return type switch which turns on only while operating it in the direction of each arrow and turns off after releasing it. The internal contact point of the cruise control main switch is turned on with the switch operation. The ECM then reads the voltage value that has been changed by the switch operation to control MODE, SET, - (COAST), RES (RESUME), + (ACCEL), and CANCEL. The dynamic laser cruise control system has two cruise control modes: the constant speed control mode and vehicle-to-vehicle distance control mode.
  1. The vehicle-to-vehicle distance control mode is always selected when starting up the dynamic laser cruise control system.
  2. The operation of the constant speed control mode is the same as that for a conventional cruise control system.

WIRING DIAGRAM


E163052E02


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM


    E117754E06
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Laser Cruise / Data List.

  1. Check the Data List for proper functioning of the cruise control main switch.

    ECM (Laser Cruise) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Main SW M-CPU
    Main switch signal (Main CPU) / ON or OFF
    ON: Main switch on
    OFF: Main switch off
    "3"
    Cancel Switch
    CANCEL switch signal / ON or OFF
    ON: CANCEL switch on
    OFF: CANCEL switch off
    -
    SET/COAST Switch
    SET/COAST switch signal / ON or OFF
    ON: - (COAST)/SET switch on
    OFF: - (COAST)/SET switch off
    -
    RES/ACC Switch
    RES/ACC switch signal / ON or OFF
    ON: + (ACCEL)/RES (RESUME) switch on
    OFF: + (ACCEL)/RES (RESUME) switch off
    -

    OK:
    When the cruise control main switch is operated, the display changes as shown above.

    Result 
    Result
    Proceed to
    OK
    A
    NG (all items are defective)
    B
    NG (1 to 3 items are defective)
    C



B
Go to step 2

C
REPLACE CRUISE CONTROL MAIN SWITCH (Click here)
A

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT CRUISE CONTROL MAIN SWITCH


  1. Remove the cruise control main switch (Click here).


    E107856E03

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Switch Condition
    Specified Condition
    A-1 (ECC) - A-2 (R/N)
    Neutral
    10 kΩ or higher
    A-1 (ECC) - A-3 (CCS)
    A-1 (ECC) - A-3 (CCS)
    + (ACCEL)/RES (RESUME)
    235 to 245 Ω
    A-1 (ECC) - A-3 (CCS)
    - (COAST)/SET
    620 to 640 Ω
    A-1 (ECC) - A-3 (CCS)
    CANCEL
    1510 to 1570 Ω
    A-1 (ECC) - A-3 (CCS)
    Main switch on
    Below 1 Ω
    A-1 (ECC) - A-2 (R/N)
    Main switch on and MODE switch on
    Below 1 Ω



NG
REPLACE CRUISE CONTROL MAIN SWITCH (Click here)
OK


3.INSPECT HARNESS AND CONNECTOR (CRUISE CONTROL MAIN SWITCH - SPIRAL CABLE)
E103330E29
  1. Disconnect the z11 connector from the spiral cable.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-1 - z11-4
    Always
    Below 1 Ω
    A-2 - z11-1
    Always
    Below 1 Ω
    A-3 - z11-3
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT SPIRAL CABLE

NOTICE:
The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the page shown in the brackets.

HINT:
  1. Removal (Click here)
  2. Installation (Click here)



    E144333E19
  1. Remove the spiral cable.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Condition
    Spiral Cable Position
    Specified Condition
    z11-1 (R/N) - H54-7 (R/N)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    z11-3 (CCS) - H54-1 (CCS)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    z11-4 (ECC) - H54-2 (ECC)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

    HINT:
    The spiral cable makes a maximum of approximately 5 rotations.

  1. Reinstall the spiral cable.



NG
REPLACE SPIRAL CABLE (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM)
  1. Disconnect the A27 connector from the ECM.

  1. Disconnect the H54 connector from the spiral cable.



    E146091E05
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H54-1 (CCS) - A27-45 (CCS)
    Always
    Below 1 Ω
    H54-7 (R/N) - A27-37 (CCHG)
    Always
    Below 1 Ω
    H54-1 (CCS) - Body ground
    Always
    10 kΩ or higher
    H54-7 (R/N) - Body ground
    Always
    10 kΩ or higher
    H54-2 (ECC) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the ECM and spiral cable connector.
    Result 
    Result
    Proceed to
    NG
    A
    OK (for 3UR-FE)
    B
    OK (for 3UR-FBE)
    C



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR