Home › Engine / Hybrid System · CRUISE CONTROL › DYNAMIC LASER CRUISE CONTROL SYSTEM

DYNAMIC LASER CRUISE CONTROL SYSTEM > Distance Control Switch Circuit

for Preparation Click here


DESCRIPTION

The distance control switch sets the vehicle-to-vehicle distance mode. The distance control switch is installed in the steering pad switch. The vehicle-to-vehicle distance set value can be changed by operating the steering pad switch (distance control switch) while the dynamic laser cruise control system is in operation.

WIRING DIAGRAM


E162413E02


INSPECTION PROCEDURE

1.INSPECT STEERING PAD SWITCH ASSEMBLY


  1. Remove the steering pad switch assembly (Click here).


    E163055E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    z12-4 (DIST) - z12-6 (ECC)
    Distance control switch is ON
    Below 1 Ω
    Distance control switch is OFF
    10 kΩ or higher

    HINT:
    When a malfunction is detected in the distance control switch, replace the steering pad switch assembly.



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK


2.INSPECT SPIRAL CABLE

NOTICE:
The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may cause airbag deployment. Be sure to read the page shown in the brackets.

HINT:
  1. Removal (Click here)
  2. Installation (Click here)



    E144333E27
  1. Remove the spiral cable.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Condition
    Spiral Cable Position
    Specified Condition
    z12-4 (DIST) - H54-11 (DIST)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    z12-6 (ECC) - H54-2 (ECC)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

    HINT:
    The spiral cable makes a maximum of approximately 5 rotations.



NG
REPLACE SPIRAL CABLE (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (DISTANCE CONTROL ECU - SPIRAL CABLE)


    E162397E03
  1. Disconnect the A43 distance control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H54-11 (DIST) - A43-16 (MODE)
    Always
    Below 1 Ω
    A43-16 (MODE) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - BODY GROUND)


    E163056E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H54-2 (ECC) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT DISTANCE CONTROL ECU


    E163057E01
  1. Remove the distance control ECU with the connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A43-16 (MODE) - Body ground
    Distance control switch ON
    Below 2 V
    A43-16 (MODE) - Body ground
    Distance control switch OFF
    11 to 14 V



NG
REPLACE DISTANCE CONTROL ECU (Click here)
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)