Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR

OUTER REAR VIEW MIRROR > INSPECTION

for Preparation Click here



1. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH


B166373E02
  1. Check the outer mirror motor operation.

    1. Apply battery voltage and check operation of the mirror face.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 10 (MV)
      Battery negative (-) → Terminal 11 (M+)
      Turns upward (A)
      Battery positive (+) → Terminal 11 (M+)
      Battery negative (-) → Terminal 10 (MV)
      Turns downward (B)
      Battery positive (+) → Terminal 11 (M+)
      Battery negative (-) → Terminal 12 (MH)
      Turns left (C)
      Battery positive (+) → Terminal 12 (MH)
      Battery negative (-) → Terminal 11 (M+)
      Turns right (D)

      If the result is not as specified, replace the outer rear view mirror assembly LH.



    B166374E02
  1. w/ Retract Mirror:
    Check the retractable mirror's movement.

    1. For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

      OK:
      Measurement Condition
      Mirror Position
      Specified Condition
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 8 (MF)
      Forward position (A)
      Moves from (A) to retracted position (E)
      Battery positive (+) → Terminal 8 (MF)
      Battery negative (-) → Terminal 7 (MR)
      Forward position (A)
      Does not move
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 8 (MF)
      Position between forward position (A) and driving position (C)
      Moves from (B) to retracted position (E)
      Battery positive (+) → Terminal 8 (MF)
      Battery negative (-) → Terminal 7 (MR)
      Position between forward position (A) and driving position (C)
      Moves from (B) to forward position (A)
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 8 (MF)
      Driving position (C)
      Moves from (C) to retracted position (E)
      Battery positive (+) → Terminal 8 (MF)
      Battery negative (-) → Terminal 7 (MR)
      Driving position (C)
      Does not move
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 8 (MF)
      Position between driving position (C) and retracted position (E)
      Moves from (D) to retracted position (E)
      Battery positive (+) → Terminal 8 (MF)
      Battery negative (-) → Terminal 7 (MR)
      Position between driving position (C) and retracted position (E)
      Moves from (D) to driving position (C)
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 8 (MF)
      Retracted position (E)
      Does not move
      Battery positive (+) → Terminal 8 (MF)
      Battery negative (-) → Terminal 7 (MR)
      Retracted position (E)
      Moves from (E) to driving position (C)

      NOTICE:
      1. Disconnect and reconnect the battery between each mirror position check.
      1. Do not apply battery voltage when moving the mirror by hand into each mirror position.

      If the result is not as specified, replace the outer rear view mirror assembly LH.



    B166835E02
  1. w/ EC Mirror:
    Check the EC mirror operation.

    1. Connect a dry battery of 1.5 V in series.

    2. Apply dry battery voltage and check operation of the mirror face, as shown in the table and illustration.

      OK:
      Measurement Connection
      Specified Condition
      Positive (+) end of the battery → Terminal 14 (EC+)
      Negative (-) end of the battery → Terminal 13 (EC-)
      Mirror surface becomes dark

      NOTICE:
      Do not apply a voltage of 1.5 V or higher.

      If the result is not as specified, replace the outer rear view mirror assembly LH.



    B166375E03
  1. w/ Mirror Heater:
    Check the mirror heater.

    1. Apply battery voltage and check the operation of the mirror heater.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 1 (+)
      Battery negative (-) → Terminal 2 (-)
      Mirror becomes warm

      HINT:
      It will take a short time for the mirror to become warm.

      If the result is not as specified, replace the outer rear view mirror assembly LH.



2. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH


B166376E03
  1. Check the outer mirror motor operation.

    1. Apply battery voltage and check operation of the mirror face.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 10 (MV)
      Battery negative (-) → Terminal 11 (M+)
      Turns upward (A)
      Battery positive (+) → Terminal 11 (M+)
      Battery negative (-) → Terminal 10 (MV)
      Turns downward (B)
      Battery positive (+) → Terminal 11 (M+)
      Battery negative (-) → Terminal 12 (MH)
      Turns left (C)
      Battery positive (+) → Terminal 12 (MH)
      Battery negative (-) → Terminal 11 (M+)
      Turns right (D)

      If the result is not as specified, replace the outer rear view mirror assembly RH.



    B166377E03
  1. w/ Retract Mirror:
    Check the retractable mirror's movement.

    1. For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

      OK:
      Measurement Condition
      Mirror Position
      Specified Condition
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 8 (MF)
      Forward position (A)
      Moves from (A) to retracted position (E)
      Battery positive (+) → Terminal 8 (MF)
      Battery negative (-) → Terminal 7 (MR)
      Forward position (A)
      Does not move
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 8 (MF)
      Position between forward position (A) and driving position (C)
      Moves from (B) to retracted position (E)
      Battery positive (+) → Terminal 8 (MF)
      Battery negative (-) → Terminal 7 (MR)
      Position between forward position (A) and driving position (C)
      Moves from (B) to forward position (A)
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 8 (MF)
      Driving position (C)
      Moves from (C) to retracted position (E)
      Battery positive (+) → Terminal 8 (MF)
      Battery negative (-) → Terminal 7 (MR)
      Driving position (C)
      Does not move
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 8 (MF)
      Position between driving position (C) and retracted position (E)
      Moves from (D) to retracted position (E)
      Battery positive (+) → Terminal 8 (MF)
      Battery negative (-) → Terminal 7 (MR)
      Position between driving position (C) and retracted position (E)
      Moves from (D) to driving position (C)
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 8 (MF)
      Retracted position (E)
      Does not move
      Battery positive (+) → Terminal 8 (MF)
      Battery negative (-) → Terminal 7 (MR)
      Retracted position (E)
      Moves from (E) to driving position (C)

      NOTICE:
      1. Disconnect and reconnect the battery between each mirror position check.
      1. Do not apply battery voltage when moving the mirror by hand into each mirror position.

      If the result is not as specified, replace the outer rear view mirror assembly RH.



    B166836E02
  1. w/ EC Mirror:
    Check the EC mirror operation.

    1. Connect a dry battery of 1.5 V in series.

    2. Apply dry battery voltage and check operation of the mirror face, as shown in the table and illustration.

      OK:
      Measurement Connection
      Specified Condition
      Positive (+) end of the battery → Terminal 14 (EC+)
      Negative (-) end of the battery → Terminal 13 (EC-)
      Mirror surface becomes dark

      NOTICE:
      Do not apply a voltage of 1.5 V or higher.

      If the result is not as specified, replace the outer rear view mirror assembly RH.



    B166378E05
  1. w/ Mirror Heater:
    Check the mirror heater.

    1. Apply battery voltage and check the operation of the mirror heater.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 1 (+)
      Battery negative (-) → Terminal 2 (-)
      Mirror becomes warm

      HINT:
      It will take a short time for the mirror to become warm.

      If the result is not as specified, replace the outer rear view mirror assembly RH.